Stripping an engine
Stripping an engine
07-12-2017, 01:12 PM
Do you want a hand??? I have a big one
(hammer that is lol) (couldnt be my ***** I'm talking about cos that's tiny lol)
Hammer lol
Do you want a hand??? I have a big one (hammer that is lol) (couldnt be my ***** I'm talking about cos that's tiny lol)
07-12-2017, 01:17 PM
Chri5 Hammer lol
Do you want a hand??? I have a big one
LOL
Just do the nuts on the head up in a sequence and then do them up again to more Nm, then do the 90 degree turn thing.
Dark Samurai
07-12-2017, 01:17 PM #3Chri5 Hammer lol
Do you want a hand??? I have a big one
LOL
Just do the nuts on the head up in a sequence and then do them up again to more Nm, then do the 90 degree turn thing.
07-12-2017, 01:40 PM
Rabster As above what tools will i need and any dooos and dont's ?
its my 1st time ill be gentle :thumbup:
no special tools mate just keep everything together ie manifold bolts beside the manifold, rocker bolts beside the rocker always use single hex sockets or you'll round the bolts off
mark the buckets i1-i8 same with the exhaust ones e1-e8 also if your removing the oil pick up remember and clean it and clean it good.
if your removing the crank watch for the two thrust washers and what way they go...if your removing the big ends you will need a 12 or 14mm multihex socket..
![[Image: ormiedit1-2.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/ormiedit1-2.jpg)
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Rabster As above what tools will i need and any dooos and dont's ?
its my 1st time ill be gentle :thumbup:
no special tools mate just keep everything together ie manifold bolts beside the manifold, rocker bolts beside the rocker always use single hex sockets or you'll round the bolts off
mark the buckets i1-i8 same with the exhaust ones e1-e8 also if your removing the oil pick up remember and clean it and clean it good.
if your removing the crank watch for the two thrust washers and what way they go...if your removing the big ends you will need a 12 or 14mm multihex socket..
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
07-12-2017, 01:40 PM
Take LOTS of Pictures and i mean LOTS!
make sure you know what nuts and bolts go where. a good method is to tape them into the holes they came from (ie when removing alternator etc)
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
07-12-2017, 01:40 PM #6Tools wise, Socket set, spanners, rachet spanners are always helpful.
Take LOTS of Pictures and i mean LOTS!
make sure you know what nuts and bolts go where. a good method is to tape them into the holes they came from (ie when removing alternator etc)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
07-12-2017, 01:54 PM
jay_russell
07-12-2017, 01:54 PM #7big can of wd40 or bolt and rust remover spray and a kettle for the tea. faster to make it in the garage than running into the house
![[Image: FB_IMG_1474048273787_zpsnbfq6a3s.jpg]](http://i1227.photobucket.com/albums/ee440/davis5835/Mobile%20Uploads/FB_IMG_1474048273787_zpsnbfq6a3s.jpg)
Recently Browsing
1 Guest(s)
1 Guest(s)
Recently Browsing
1 Guest(s)
1 Guest(s)
Related Threads…
Replies 8
Views 240
Views 240
26-12-2020, 11:25 AM
Last Post bybigdave1701
Last Post by
Replies 9
Views 166
Views 166
30-04-2020, 10:51 PM
Last Post byZAIS200
Last Post by
Replies 18
Views 846
Views 846
09-06-2018, 10:54 PM
Last Post byPhil01
Last Post by
Replies 1
Views 192
Views 192
08-06-2018, 01:42 AM
Last Post byBOOSST
Last Post by
Replies 0
Views 167
Views 167
19-05-2018, 02:32 PM
Last Post bypulsar_stu
Last Post by
Replies 1
Views 187
Views 187
06-05-2018, 07:41 AM
Last Post byjay_russell
Last Post by
Replies 12
Views 615
Views 615
24-04-2018, 05:26 AM
Last Post byjimxms
Last Post by
Replies 21
Views 969
Views 969
18-04-2018, 10:12 AM
Last Post bydaz@likwidart
Last Post by
Replies 9
Views 542
Views 542
20-05-2017, 11:41 PM
Last Post byparthiban
Last Post by