anti roll bar links
anti roll bar links
1 of mine is fecked and it looks like the roll bar has gone with it, as norm the nut is seized, i suspect the taper was worn and has now elongated the hole in the roll bar.
Unless someone has a set of TTE roll bars for sale?? :w00t:
anone have a PN for the rear links and rear roll bar???
1 of mine is fecked and it looks like the roll bar has gone with it, as norm the nut is seized, i suspect the taper was worn and has now elongated the hole in the roll bar.
Unless someone has a set of TTE roll bars for sale?? :w00t:
Rear- 48830‑51010 LH/RH
Front- 48820‑22041 LH/RH
REAR STABILIZER BAR:-
Parts listed,
48812‑51010 GXE10
48812‑53010 GXE10..SED..EUR; GXE10..MTM..ARL; W(STAINLESS SCUFF PLATE)
48812‑53020 GXE10; JCE10..WG
Lexus IS200 Sport Navigator (Now being stripped again) :blink:
Now Don't Forget The REP!!!
Drop link part number
Rear- 48830‑51010 LH/RH
Front- 48820‑22041 LH/RH
REAR STABILIZER BAR:-
Parts listed,
48812‑51010 GXE10
48812‑53010 GXE10..SED..EUR; GXE10..MTM..ARL; W(STAINLESS SCUFF PLATE)
48812‑53020 GXE10; JCE10..WG
Lexus IS200 Sport Navigator (Now being stripped again) :blink:
Now Don't Forget The REP!!!
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
09-07-2016, 09:09 AM #4You should be able to get a rear ARB from a breaker's (I presume you have them over there ?). Might be a good excuse to get a new uprated set though !
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
i did think about getting a trd or hotchkis set and repainting them but the extra holes might lead to questions i dont need.
would love to get an aftermarket set but as the swiss are naziesqe when i comes to car mods ( or cars in general) i would be limited to eibach/tte at best. I cant be bother to swap between standard and aftermarket bars before the check either, even if it is every 2 years.
i did think about getting a trd or hotchkis set and repainting them but the extra holes might lead to questions i dont need.
Although Wozza's solution sounds like the best one to me ! :biggrin:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
09-07-2016, 10:51 PM #6Doh, I forgot about the problems with modding in Switzerland. Wouldn't it be pretty straightforward just to weld the offending hole on the OEM ARB though ?
Although Wozza's solution sounds like the best one to me ! :biggrin:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
DJ Wozza If it will help Rob, you can buy a set of Hotchkis and pay a garage to fit them to mine, then pay for shipping on my TTE Reds to you
no worries mate, just ive me all of your account numbers and full details and ill pass it to my mate umgeni in nigeria to make the payments......:Fish:
haha.
DJ Wozza If it will help Rob, you can buy a set of Hotchkis and pay a garage to fit them to mine, then pay for shipping on my TTE Reds to you
no worries mate, just ive me all of your account numbers and full details and ill pass it to my mate umgeni in nigeria to make the payments......:Fish:
haha.
Because my understanding is it the car that insured and not the driver.
So any items that have been added by the dealer are ok and anything you add will not be classed as legal after market items.
I sure you can put me right on this subject so i fully understand.
Rob when you mod a car can this only be done in a main dealers in Switzerland?
Because my understanding is it the car that insured and not the driver.
So any items that have been added by the dealer are ok and anything you add will not be classed as legal after market items.
I sure you can put me right on this subject so i fully understand.
If done right :ohmy:
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
Once it is welded then ground flush and repainted it would look like new and not Gash:Fish:
If done right :ohmy:
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
1 Guest(s)
1 Guest(s)
Views 1,584
Last Post by
Views 1,161
Last Post by