Daylight Running Lights
Daylight Running Lights
17-06-2018, 11:45 PM
One important thing to note when fitted LED strips, it to have the correct protection (a fuse and a diode, I think) as there is at least one instance of them catching fire! Properly fitted, this should not be possible though.
![[Image: tempsig2.jpg]](http://i121.photobucket.com/albums/o227/84stoney/tempsig2.jpg)
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:There was a phase a couple of years back where a lot of people were fitting LED strips above the headlights. This phase seems to mostly have passed. Rabster had some recently, but I believe the new owner of the car has/plans to remove them.
One important thing to note when fitted LED strips, it to have the correct protection (a fuse and a diode, I think) as there is at least one instance of them catching fire! Properly fitted, this should not be possible though.
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:
18-06-2018, 12:07 AM
Eyebrow fitting guide
Eye Brows or Angel Eyes
(A thread I started a few years back.)
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:You may find these links in some way helpful:
Eyebrow fitting guide
Eye Brows or Angel Eyes
(A thread I started a few years back.)
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:
18-06-2018, 12:23 AM
DJ Wozza I would suggest a quick blow fuse and a diode to stop any feedback current if a single LED fails in the strip
This is what I (and some other Outlaw Jap Club members) have been using for electrical safety.
Maplins
Diode - QL73Q
Fuse holder 20mm- PC78K
Fuse quick blow 20mm, 500mA - GJ85G
Obviously it is up to you if you want to use any of these components, and only do so if you are competent @ electrics. The diode is for stopping any feedback currents, and I have been told by an electrical engineer that is is a good move incase of strip failure (one LOC members set caught fire but may have being wired incorrectly).
Edited 30-07-2011, 09:58 AM by Stoney.
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:That guide above states a quick blow fuse, but I knew a diode was a good extra precaution too:
DJ Wozza I would suggest a quick blow fuse and a diode to stop any feedback current if a single LED fails in the strip
This is what I (and some other Outlaw Jap Club members) have been using for electrical safety.
Maplins
Diode - QL73Q
Fuse holder 20mm- PC78K
Fuse quick blow 20mm, 500mA - GJ85G
Obviously it is up to you if you want to use any of these components, and only do so if you are competent @ electrics. The diode is for stopping any feedback currents, and I have been told by an electrical engineer that is is a good move incase of strip failure (one LOC members set caught fire but may have being wired incorrectly).
ad: It was a tough call to make, but the Supercharged IS200 is being retired. ad:
Recently Browsing
2 Guest(s)
2 Guest(s)
Recently Browsing
2 Guest(s)
2 Guest(s)
Related Threads…
Replies 10
Views 481
Views 481
08-04-2021, 11:45 PM
Last Post byozzie b
Last Post by
Replies 2
Views 159
Views 159
07-10-2020, 01:46 AM
Last Post byStoney
Last Post by
Replies 3
Views 298
Views 298
27-06-2019, 10:44 AM
Last Post byel_bandido
Last Post by
Replies 26
Views 1,091
Views 1,091
20-03-2019, 03:09 AM
Last Post bytoxo
Last Post by
Replies 11
Views 718
Views 718
26-01-2019, 04:13 AM
Last Post byis300_dino
Last Post by
Replies 27
Views 1,647
Views 1,647
26-11-2018, 05:36 AM
Last Post bydavidjamesbattersby
Last Post by
Replies 15
Views 713
Views 713
28-09-2018, 02:22 PM
Last Post bydavidjamesbattersby
Last Post by