supercharger pulley
supercharger pulley
just sealed up the intake and outlet on the charger,will fit in the morn and see what sound it makes,hope the bearings ain't shagged or i shall cry......
i think the next prob will be setting the spring on the bov,as im not running a bypass.so that it kicks in at around 3000rpm..that should do it me thinks.
got to do the boost guage as well....will it never end.lol
buzzard2011
26-11-2018, 01:04 PM #31yeah will do dimis thanks for the support.,but ill be buggered if i take the cradle out for some pics,ill leave it in.
just sealed up the intake and outlet on the charger,will fit in the morn and see what sound it makes,hope the bearings ain't shagged or i shall cry......
i think the next prob will be setting the spring on the bov,as im not running a bypass.so that it kicks in at around 3000rpm..that should do it me thinks.
got to do the boost guage as well....will it never end.lol
i'd suggest getting a SSQV over a normal BOV mate, works off inlet pressure rather than spring pressure, better for what you want
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
27-11-2018, 02:18 PM #32sounds like youve made progress mate,
i'd suggest getting a SSQV over a normal BOV mate, works off inlet pressure rather than spring pressure, better for what you want
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
got the charger running today,sounds sweet.,an load nearly sucked my hand in through the intake though
cared:,jeez them bloers have a lot of suction lmao.still getting vibrations though,i think ill try a heavier craddle next week if i got time.tried posting pics but got bored trying........:mad:
buzzard2011
27-11-2018, 03:17 PM #33yeah,was looking into a ssqv,then bought a greddy rz cheap should be ok,, maybe,.
got the charger running today,sounds sweet.,an load nearly sucked my hand in through the intake thoughcared:,jeez them bloers have a lot of suction lmao.
still getting vibrations though,i think ill try a heavier craddle next week if i got time.tried posting pics but got bored trying........:mad:
Partnumber: G15-22-21
Producer & Producer partnumber:
MERCEDES BENZ: 6032050110
Mercedes analogy numbers:
6032050110, A6032050110
youll need to redrill it though not a problem.:w00t:
buzzard2011
22-12-2018, 01:28 AM #35hope this helps.
Partnumber: G15-22-21
Producer & Producer partnumber:
MERCEDES BENZ: 6032050110
Mercedes analogy numbers:
6032050110, A6032050110
youll need to redrill it though not a problem.:w00t:
http://www.ebay.co.uk/itm/150PC-SPRING-A...35b8c5fe71
Stoney try this for a new bypass spring (if you havnt got a replacement already):
http://www.ebay.co.uk/itm/150PC-SPRING-A...35b8c5fe71
1. Has anyone run the 138mm pulley for a while and can confirm that it works and is safe?
2. Will it line up with the supercharger okay if I'm using an original TTE cradle?
3. Does anyone know the PCD of the holes on the IS200 water pump that need drilling into the 138mm pulley?
sprinter2012
31-05-2019, 12:08 PM #38Sorry to drag up an old thread, but I'm hoping a couple of you guys who are subscribed to it can answer my questions
1. Has anyone run the 138mm pulley for a while and can confirm that it works and is safe?
2. Will it line up with the supercharger okay if I'm using an original TTE cradle?
3. Does anyone know the PCD of the holes on the IS200 water pump that need drilling into the 138mm pulley?
A few people in Europe have run the bigger pulley and yes it lines up.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
31-05-2019, 12:39 PM #39Could you not take off the little pully cover to get the pcd?
A few people in Europe have run the bigger pulley and yes it lines up.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav Could you not take off the little pully cover to get the pcd?
A few people in Europe have run the bigger pulley and yes it lines up.
I'd need to get the bolts out to get an accurate measurement though wouldn't I? And I don't want to do that until I actually come to fitting it.
And is it that exact pulley (the mercedes one posted above) that they used?
sprinter2012
31-05-2019, 01:00 PM #40Sparkystav Could you not take off the little pully cover to get the pcd?
A few people in Europe have run the bigger pulley and yes it lines up.
I'd need to get the bolts out to get an accurate measurement though wouldn't I? And I don't want to do that until I actually come to fitting it.
And is it that exact pulley (the mercedes one posted above) that they used?
5 Guest(s)
5 Guest(s)
Views 1,851
Last Post by
Views 720
Last Post by
Views 468
Last Post by
Views 931
Last Post by
Views 110
Last Post by
Views 86
Last Post by
Views 410
Last Post by
Views 424
Last Post by