drive train diagrams?
drive train diagrams?
Cheers!
el_bandido
17-12-2018, 07:29 AM #1I'm about to have a poke about underneath my car to find what is causing this irritating noise. Anyone got either a diagram of gearbox to diff or a **** good set of pictures with some arrows pointing at the bits that could be rattling?
Cheers!
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
is300_dino
17-12-2018, 08:04 AM #2have you looked at the bahamute site im sure there will be some info your after on there mate
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
Anyone got any idea how much money I should be looking at for the lower arm bush replacement? It's the one right by the brake disk/drum assembly.
el_bandido
17-12-2018, 09:06 AM #3I reckon it's actually a bush in the rear lower arm causing the problem anyway, we checked that out and ran it in gear with the wheels off. No noise at all, even at 5000 rpm
Anyone got any idea how much money I should be looking at for the lower arm bush replacement? It's the one right by the brake disk/drum assembly.
Which bush in these diagrams ?
![[Image: IS200frontsuspension.png]](http://i5.photobucket.com/albums/y179/SteveHammatt/IS200frontsuspension.png)
![[Image: IS200rearsuspension.png]](http://i5.photobucket.com/albums/y179/SteveHammatt/IS200rearsuspension.png)
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
19-01-2019, 11:14 PM #4Are you still working on this ? If so, is it front or rear ? (I am guessing rear by you mentioning the diff)
Which bush in these diagrams ?
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
Thanks for those diagrams, I'll definitely be needing them again.
el_bandido
19-01-2019, 11:30 PM #5Stevie - I've bought a replacement for the loose one already! It's 90105-14082(2). Going to take it down to John at some point and fit them in, then get the front wheel bearings done.
Thanks for those diagrams, I'll definitely be needing them again.
el_bandido Stevie - I've bought a replacement for the loose one already! It's 90105-14082(2). Going to take it down to John at some point and fit them in, then get the front wheel bearings done.
Thanks for those diagrams, I'll definitely be needing them again.
No problem, but sorry, that part is just a bolt/nut/washer combo, isn't it ? Not the bush, which seems to be part of the suspension arm itself ? So was it the bolt itself that was the problem and not the bush ?
Some bushes are available separately, but for some you have to get a whole arm unless you can find a third-party alternative.
Sorry if I am going over old stuff which is already sorted though.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
19-01-2019, 11:48 PM #6el_bandido Stevie - I've bought a replacement for the loose one already! It's 90105-14082(2). Going to take it down to John at some point and fit them in, then get the front wheel bearings done.
Thanks for those diagrams, I'll definitely be needing them again.
No problem, but sorry, that part is just a bolt/nut/washer combo, isn't it ? Not the bush, which seems to be part of the suspension arm itself ? So was it the bolt itself that was the problem and not the bush ?
Some bushes are available separately, but for some you have to get a whole arm unless you can find a third-party alternative.
Sorry if I am going over old stuff which is already sorted though.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
el_bandido
20-01-2019, 01:29 AM #7I've got a whole new pair of arms with camber adjustable polybushes. They might need pressing, but I'll be taking them up to the J-unit for fitting
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
20-01-2019, 01:37 AM #9Cool
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
2 Guest(s)
2 Guest(s)