LS400 Optitron Dials
LS400 Optitron Dials
There is a bit of damage to the 'hood' over the top of the dials but this isn't an issue if you were to swap them into something else.
Don't have a photo of mine specifically but they look like this:
![[Image: wpid-100_3393-2011-03-20-01-35.jpg]](http://jesda.com/wp-content/uploads/2011/03/wpid-100_3393-2011-03-20-01-35.jpg)
This photo doesn't do them justice really, they are REALLY bright!
You can sort of see them in this video
http://www.youtube.com/watch?v=wcn2yFSjeT4
My intention was to fit the dials into the MR2 cluster to achieve something like this:
http://www.youtube.com/watch?v=t_qp40xGeyE
I've got a set of dials from my LS400 that I was going to use but I've now changed my mind. They are 'Optitron' gauges so they light up with CCFL tubes and have LED needles. I have the complete cluster, and all the wiring connectors for it with wire tails on. The display also has a small screen in it but I'm not sure you if you can do much with that - it is a separate part inside the dials so easily removable/replaceable.
There is a bit of damage to the 'hood' over the top of the dials but this isn't an issue if you were to swap them into something else.
Don't have a photo of mine specifically but they look like this:
This photo doesn't do them justice really, they are REALLY bright!
You can sort of see them in this video
http://www.youtube.com/watch?v=wcn2yFSjeT4
My intention was to fit the dials into the MR2 cluster to achieve something like this:
http://www.youtube.com/watch?v=t_qp40xGeyE
Here are some pictures of the unit. These are quite big images so that you can see detail:
Hood off:
![[Image: IMGP3267.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3267.jpg)
Hood (some damage top right as you can see - irrelevant if you're installing into an MR2's cluster):
![[Image: IMGP3268.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3268.jpg)
Rear of unit with main board removed. You can see the membrane wiring for the warning lights, 4 connection points for each dial and the white and red wiring connectors for the CCFL tubes that light up the dials:
![[Image: IMGP3269.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3269.jpg)
Multi-display is a separate part, easily removed:
![[Image: IMGP3270.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3270.jpg)
Unit with screen removed:
![[Image: IMGP3271.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3271.jpg)
Rear of unit with screen removed:
![[Image: IMGP3281.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3281.jpg)
Rear of unit with main PCB reattached - like the MR2 cluster it uses long screws to transmit signals through to the gauges. This PCB also contains the inverter circuitry for the CCFL tubes:
![[Image: IMGP3282.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3282.jpg)
Unit completely assembled including multi-display PCB:
![[Image: IMGP3283.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3283.jpg)
Dimensions:
![[Image: IMGP3272.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3272.jpg)
![[Image: IMGP3273.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3273.jpg)
![[Image: IMGP3274.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3274.jpg)
![[Image: IMGP3275.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3275.jpg)
![[Image: IMGP3276.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3276.jpg)
![[Image: IMGP3277.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3277.jpg)
![[Image: IMGP3278.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3278.jpg)
![[Image: IMGP3279.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3279.jpg)
![[Image: IMGP3280.jpg]](http://theshado.ws/images/LS400/instrumentCluster/IMGP3280.jpg)
Wiring Diagram:
http://theshado.ws/images/LS400/instrume.../be-86.pdf
The front of the unit says 1025REV=1MILE.
ODO was 117,000 miles.
Here are some pictures of the unit. These are quite big images so that you can see detail:
Hood off:
Hood (some damage top right as you can see - irrelevant if you're installing into an MR2's cluster):
Rear of unit with main board removed. You can see the membrane wiring for the warning lights, 4 connection points for each dial and the white and red wiring connectors for the CCFL tubes that light up the dials:
Multi-display is a separate part, easily removed:
Unit with screen removed:
Rear of unit with screen removed:
Rear of unit with main PCB reattached - like the MR2 cluster it uses long screws to transmit signals through to the gauges. This PCB also contains the inverter circuitry for the CCFL tubes:
Unit completely assembled including multi-display PCB:
Dimensions:
Wiring Diagram:
http://theshado.ws/images/LS400/instrume.../be-86.pdf
The front of the unit says 1025REV=1MILE.
1 Guest(s)
1 Guest(s)
Views 457
Last Post by