Painted my Callipers
Painted my Callipers
04-05-2017, 01:18 AM
Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R
NIce work Dave, looking forward to the walk through:thumbup1:
Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R
04-05-2017, 10:25 AM
todd Good guide, need to do mine again at some point fairly soon.
Always found that putting the tin of paint in a small bowl of hot water (with the lid off) made it so much easier to work with.
That's a very good tip. I always find the paint a little on the thick side. I have tried thinning it down in the past.
todd Good guide, need to do mine again at some point fairly soon.
Always found that putting the tin of paint in a small bowl of hot water (with the lid off) made it so much easier to work with.
That's a very good tip. I always find the paint a little on the thick side. I have tried thinning it down in the past.
11-05-2017, 09:19 AM
Dave did you give yours a coat of lacquer after you applied them, as this seals them and keeps the **** off them.
Shame about your type of locking wheel nut, that type always look so dirty and black- spoils the whole look of the wheel. My brother has the same prob with his Avensis.
1990 Eunos Roadster in Mariner DU blue
Cobalt cat back, Decat pipe, 15in Red Rota GT3 alloys, Toyo tyres, Lowered on Coil overs, Red anti roll bars, 14degree timing mod, white dash kit, illuminated side marker lights,
Halo ring headlights, OEM windblocker, Bluetooth streaming HU, Blue leather handbrake and gear lever gaitor, Centre brake/tail light mod, Blue velour door cards, Polished cam cover, Polished front strut bar, 4xheadrest speakers, JDM floor mats, Suede semi dish steering wheel,
Painted my calipers red, and just ordered some White Carbon decals.
Dave did you give yours a coat of lacquer after you applied them, as this seals them and keeps the **** off them.
Shame about your type of locking wheel nut, that type always look so dirty and black- spoils the whole look of the wheel. My brother has the same prob with his Avensis.
1990 Eunos Roadster in Mariner DU blue
Cobalt cat back, Decat pipe, 15in Red Rota GT3 alloys, Toyo tyres, Lowered on Coil overs, Red anti roll bars, 14degree timing mod, white dash kit, illuminated side marker lights,
Halo ring headlights, OEM windblocker, Bluetooth streaming HU, Blue leather handbrake and gear lever gaitor, Centre brake/tail light mod, Blue velour door cards, Polished cam cover, Polished front strut bar, 4xheadrest speakers, JDM floor mats, Suede semi dish steering wheel,
11-05-2017, 09:23 AM
I have to agree with you on the locking nuts they don't look nice. I polished up the other wheel nuts while they were off though
Recently Browsing
3 Guest(s)
3 Guest(s)
Recently Browsing
3 Guest(s)
3 Guest(s)
Related Threads…
Replies 11
Views 718
Views 718
26-01-2019, 04:13 AM
Last Post byis300_dino
Last Post by
Replies 3
Views 368
Views 368
26-11-2017, 01:06 PM
Last Post bydimis
Last Post by
Replies 20
Views 926
Views 926
11-12-2016, 12:47 PM
Last Post byRabster
Last Post by