JapCarForum Cars, Cars, Cars! Project Cars Mitsubishi Super VR4

Mitsubishi Super VR4

Mitsubishi Super VR4

Pages (14): Previous 1 2 3 4 5 614 Next  
Chri5
Posting Freak
1,894
12-05-2017, 10:40 AM
#31
For the rattle cans I also warm them in boiling water before commencing Wink

good job so far
looks so much cleaner and less SOT :thumbup:
Chri5
12-05-2017, 10:40 AM #31

For the rattle cans I also warm them in boiling water before commencing Wink

good job so far
looks so much cleaner and less SOT :thumbup:

Mazz
Senior Member
265
25-05-2017, 09:22 AM
#32
PART V


With the new rear lip fitted, the Powerflow exhaust that had been fitted was now too short.

However, our other VR-4 has a Blueflame exhaust, which sits a lot further out from the exhaust.

A quick removal of the two exhausts:

[Image: IMG_0154.jpg]
[Image: IMG_0168.jpg]

And installation on the other car, and the exhausts sit much nicer now on both cars:

[Image: IMG_0190.jpg]
[Image: IMG_0191.jpg]
[Image: IMG_0192.jpg]
[Image: IMG_0193.jpg]

Eventually a dual-exit system will be made, but this is the best compromise for now. The other cut-out in the rear lip will soon home a fog light.


Next up... audio!

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
25-05-2017, 09:22 AM #32

PART V


With the new rear lip fitted, the Powerflow exhaust that had been fitted was now too short.

However, our other VR-4 has a Blueflame exhaust, which sits a lot further out from the exhaust.

A quick removal of the two exhausts:

[Image: IMG_0154.jpg]
[Image: IMG_0168.jpg]

And installation on the other car, and the exhausts sit much nicer now on both cars:

[Image: IMG_0190.jpg]
[Image: IMG_0191.jpg]
[Image: IMG_0192.jpg]
[Image: IMG_0193.jpg]

Eventually a dual-exit system will be made, but this is the best compromise for now. The other cut-out in the rear lip will soon home a fog light.


Next up... audio!


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

Mazz
Senior Member
265
25-05-2017, 09:36 AM
#33
cheers Smile
yes thats why we went for the twin cut out, cost us about £20 more for it, but its soooo worth it!
pitty non of these rear lips will be made again as these are one off;s Smile

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
25-05-2017, 09:36 AM #33

cheers Smile
yes thats why we went for the twin cut out, cost us about £20 more for it, but its soooo worth it!
pitty non of these rear lips will be made again as these are one off;s Smile


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

Mazz
Senior Member
265
25-05-2017, 09:37 AM
#34
in fact the rear lip is only 1 of 2 in the world! Big Grin

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
25-05-2017, 09:37 AM #34

in fact the rear lip is only 1 of 2 in the world! Big Grin


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

Mazz
Senior Member
265
25-05-2017, 10:13 AM
#35
tis good, but a PITA if anything should (god forbid!) happen!

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
25-05-2017, 10:13 AM #35

tis good, but a PITA if anything should (god forbid!) happen!


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

garyskisplym
Senior Member
714
26-05-2017, 09:14 AM
#36
very nice

like the rear lip.

Will look mental with twin exit exhaust

BHP, TORQUE, UNDER STEER, OVERSTEER FOR DUMMYS
BHP- how fast you hit the wall, TORQUE- how far you push the wall
OVER STEER- Dont see the wall, UNDER STEER- You do see it
1999 Blue IS200 SportTRD kit, K&N Filter
garyskisplym
26-05-2017, 09:14 AM #36

very nice

like the rear lip.

Will look mental with twin exit exhaust


BHP, TORQUE, UNDER STEER, OVERSTEER FOR DUMMYS
BHP- how fast you hit the wall, TORQUE- how far you push the wall
OVER STEER- Dont see the wall, UNDER STEER- You do see it
1999 Blue IS200 SportTRD kit, K&N Filter

Mazz
Senior Member
265
29-06-2017, 05:58 AM
#37
sorry iv been a bit on the quite side, been a bit busy with the car.

bit of an update to add, but in short she has tax and test......

now..... Big Grin






PART VI


Not only the exterior had cosmetic differences on the Super VR-4. The differences extended to the interior, where it gained red carpet, red/black gear lever & handbrake, red/black Momo steering wheel, purple-tinted dash gauges, and "carbon fibre" effect dash surround. Also on the list is are red/black door cards, rear seats, and matching Recaro fully adjustable front seats.

Most of this, fortunately, is present, other than the Recaro front seats, which have been replaced with other seats following a similar patterning to the doors, but only in blue, rather than red!

The steering wheel, too, has seen better days, with the red part VERY faded and damaged.

[Image: IMG_9839.jpg]

So, the aim has been to try to acquire the Recaro seats, a replacement steering wheel to restore the interior to factory "Super VR-4" standard.


Unfortunately for others, but very fortunately for us, we have managed to acquire not only these parts, but also original front canards, and sideskirts - from another complete Super VR-4 - this time, however, a Galant saloon:

[Image: 101_3663.jpg]
[Image: 101_3329.jpg]
[Image: 101_3141.jpg]

And, now, the love-child of our other two Smile
[Image: IMG_0283.jpg]

Unfortunately, this is how it was delivered to us...

[Image: IMG_0280.jpg]

The damage is, regrettably, terminal.

[Image: IMG_0297.jpg]
[Image: IMG_0293.jpg]
[Image: IMG_0290.jpg]
[Image: IMG_0289.jpg]
[Image: IMG_0287.jpg]

(We would like to meet the person who did this to the car... and punch them in the ovaries)

However - every cloud has a silver lining, and in this case, it means that the Legnum can now have the correct OEM parts - Recaro's, skirts, canards, and a steering wheel in better condition than the one currently there.

The plus side, too, is that by breaking the saloon for parts, we'll be able to make a bit of money back on it.

Every time we've gone outside today and seen that parked up there, it's made us feel physically sick seeing the damage to it, and knowing we can't fix it Sad

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
29-06-2017, 05:58 AM #37

sorry iv been a bit on the quite side, been a bit busy with the car.

bit of an update to add, but in short she has tax and test......

now..... Big Grin






PART VI


Not only the exterior had cosmetic differences on the Super VR-4. The differences extended to the interior, where it gained red carpet, red/black gear lever & handbrake, red/black Momo steering wheel, purple-tinted dash gauges, and "carbon fibre" effect dash surround. Also on the list is are red/black door cards, rear seats, and matching Recaro fully adjustable front seats.

Most of this, fortunately, is present, other than the Recaro front seats, which have been replaced with other seats following a similar patterning to the doors, but only in blue, rather than red!

The steering wheel, too, has seen better days, with the red part VERY faded and damaged.

[Image: IMG_9839.jpg]

So, the aim has been to try to acquire the Recaro seats, a replacement steering wheel to restore the interior to factory "Super VR-4" standard.


Unfortunately for others, but very fortunately for us, we have managed to acquire not only these parts, but also original front canards, and sideskirts - from another complete Super VR-4 - this time, however, a Galant saloon:

[Image: 101_3663.jpg]
[Image: 101_3329.jpg]
[Image: 101_3141.jpg]

And, now, the love-child of our other two Smile
[Image: IMG_0283.jpg]

Unfortunately, this is how it was delivered to us...

[Image: IMG_0280.jpg]

The damage is, regrettably, terminal.

[Image: IMG_0297.jpg]
[Image: IMG_0293.jpg]
[Image: IMG_0290.jpg]
[Image: IMG_0289.jpg]
[Image: IMG_0287.jpg]

(We would like to meet the person who did this to the car... and punch them in the ovaries)

However - every cloud has a silver lining, and in this case, it means that the Legnum can now have the correct OEM parts - Recaro's, skirts, canards, and a steering wheel in better condition than the one currently there.

The plus side, too, is that by breaking the saloon for parts, we'll be able to make a bit of money back on it.

Every time we've gone outside today and seen that parked up there, it's made us feel physically sick seeing the damage to it, and knowing we can't fix it Sad


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

Mazz
Senior Member
265
29-06-2017, 05:59 AM
#38
and thats not all!!!.....



MUHAHAHAHAHAHA!!!!!!



PART VII

Super VR4's came with an option for tri-spoke wheels.


[Image: IMG_0397.jpg]

[Image: IMG_0393.jpg]

[Image: IMG_0391.jpg]

They're not the official optional wheels, but instead some Ray's 3-piece split wheels - and they give the car a completely different look.

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
29-06-2017, 05:59 AM #38

and thats not all!!!.....



MUHAHAHAHAHAHA!!!!!!



PART VII

Super VR4's came with an option for tri-spoke wheels.


[Image: IMG_0397.jpg]

[Image: IMG_0393.jpg]

[Image: IMG_0391.jpg]

They're not the official optional wheels, but instead some Ray's 3-piece split wheels - and they give the car a completely different look.


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

Mazz
Senior Member
265
29-06-2017, 06:00 AM
#39
oh and this.......


PART VIII

Now that the Super saloon has arrived, it's time to pillage for parts.

First on the list, as they're the easiest & cheapest to prepare, is the sideskirts.

The facelift skirts fitted in an earlier update are of course not the correct parts for a Super, so, they've got to come off again.

Unfortunately, the saloon has had quite a bad time in it's life, and quite a few bits are quite battered (other than the obvious rear end damage, the driver's side rear quarter has been previously repaired, as in some parts there is now 2-3mm of body filler visible, and flaking off!)

Additionally, the passenger sideskirt has been previously damaged, and repaired with filler. Some of this was flaking off, so we removed the damaged bits, and set to repairing it again ourselves.

[Image: IMG_0455.jpg]

Fill, sand, rinse, fill, sand, rinse, repeat...

And then some paint:

[Image: IMG_0456.jpg]

Brackets to hold top of skirt to body:

[Image: IMG_0459.jpg]

Plus some double-sided tape:

[Image: IMG_0457.jpg]

And on they go:

[Image: IMG_0461.jpg]

[Image: IMG_0462.jpg]

[Image: IMG_0465.jpg]

In the dark i watch and wait......
[Image: IMG_9151SIG.png]
Mazz
29-06-2017, 06:00 AM #39

oh and this.......


PART VIII

Now that the Super saloon has arrived, it's time to pillage for parts.

First on the list, as they're the easiest & cheapest to prepare, is the sideskirts.

The facelift skirts fitted in an earlier update are of course not the correct parts for a Super, so, they've got to come off again.

Unfortunately, the saloon has had quite a bad time in it's life, and quite a few bits are quite battered (other than the obvious rear end damage, the driver's side rear quarter has been previously repaired, as in some parts there is now 2-3mm of body filler visible, and flaking off!)

Additionally, the passenger sideskirt has been previously damaged, and repaired with filler. Some of this was flaking off, so we removed the damaged bits, and set to repairing it again ourselves.

[Image: IMG_0455.jpg]

Fill, sand, rinse, fill, sand, rinse, repeat...

And then some paint:

[Image: IMG_0456.jpg]

Brackets to hold top of skirt to body:

[Image: IMG_0459.jpg]

Plus some double-sided tape:

[Image: IMG_0457.jpg]

And on they go:

[Image: IMG_0461.jpg]

[Image: IMG_0462.jpg]

[Image: IMG_0465.jpg]


In the dark i watch and wait......
[Image: IMG_9151SIG.png]

SHAHZ
Posting Freak
2,142
29-06-2017, 06:06 AM
#40
Nice work :thumbup::thumbup1:.....mmmmmm loving the saloon, shame about the rear end, coming along nicely nowConfusedmoke:

Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R
SHAHZ
29-06-2017, 06:06 AM #40

Nice work :thumbup::thumbup1:.....mmmmmm loving the saloon, shame about the rear end, coming along nicely nowConfusedmoke:


Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R

Pages (14): Previous 1 2 3 4 5 614 Next  
Recently Browsing
 10 Guest(s)
Recently Browsing
 10 Guest(s)
Related Threads…
Replies 7
Views 716
01-09-2020, 03:21 AM
Last Post by mit3000gto
Replies 11
Views 1,025
26-08-2019, 09:26 AM
Last Post by RichiesTrucking
Replies 130
Views 6,715
21-03-2019, 12:32 AM
Last Post by AaronR33