Project: DIY Supercharger

JapCarForum Car Manufacturers Lexus/Toyota IS200 / IS300 / SPORTCROSS / Altezza Project: DIY Supercharger

Pages (15): Previous 1 2 3 4 5 … 15 Next

Lexuspat
Administrator

6,827

02-04-2019, 11:18 AM

#11

I've got some pics that members sent me of there cradles mate ill send them onto you,

[Image: FB_IMG_1474048273787_zpsnbfq6a3s.jpg]

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat

02-04-2019, 11:18 AM #11

I've got some pics that members sent me of there cradles mate ill send them onto you,

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat
Administrator

6,827

02-04-2019, 11:30 AM

#12

I'm gonna leave my induction kit on until I've built the kit, posty is up at RSCS so may try and get a sneaky look at his cradle

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat

02-04-2019, 11:30 AM #12

I'm gonna leave my induction kit on until I've built the kit, posty is up at RSCS so may try and get a sneaky look at his cradle

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

sprinter2012
Posting Freak

2,484

02-04-2019, 11:36 AM

#13

Lexuspat I'm gonna leave my induction kit on until I've built the kit, posty is up at RSCS so may try and get a sneaky look at his cradle

I would have liked to leave it on, but I would have to take it off every time I wanted to test fit the cradle or measure something so I decided it needed to go.

Plus I can put the funds towards buying an actual charger to build the cradle around.

sprinter2012

02-04-2019, 11:36 AM #13

Lexuspat I'm gonna leave my induction kit on until I've built the kit, posty is up at RSCS so may try and get a sneaky look at his cradle

Lexuspat
Administrator

6,827

02-04-2019, 11:49 AM

#14

That's a good point, what size pipe are you gonna use and is it mild steel your using

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat

02-04-2019, 11:49 AM #14

That's a good point, what size pipe are you gonna use and is it mild steel your using

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

sprinter2012
Posting Freak

2,484

02-04-2019, 11:54 AM

#15

I'll probably make it out of aluminium if I can, as it will save a lot of weight and it will be much easier to work with. Plus our aluminium cut-off saw at work gives a much better finish than our band saw would on steel.

Not decided on size yet, I'll probably make it out of the same diameter material as the mounting posts on the charger, if that makes sense?

Edited 13-05-2012, 09:29 PM by sprinter2012.

sprinter2012

02-04-2019, 11:54 AM #15

Lexuspat
Administrator

6,827

02-04-2019, 03:10 PM

#16

Good I really need to get on and do this so I can have a charger I thinks that's what's bringing me down slightly and why I keep looking at different cars

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat

02-04-2019, 03:10 PM #16

Good I really need to get on and do this so I can have a charger I thinks that's what's bringing me down slightly and why I keep looking at different cars

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Fozzy
Posting Freak

1,132

02-04-2019, 03:18 PM

#17

You still worried about the cradle, check what I made for stav, then ask me again if I can make what you need

2009 JAE Car Pull Runner Up
2010 JAE Car Pull Failure

My Garage

Fozzy

02-04-2019, 03:18 PM #17

You still worried about the cradle, check what I made for stav, then ask me again if I can make what you need

2009 JAE Car Pull Runner Up
2010 JAE Car Pull Failure

My Garage

Lexuspat
Administrator

6,827

02-04-2019, 03:22 PM

#18

I know you can make what I need Pete :thumbup:

So stop wasting time and make me and sprinter a cradle so we can finally charge our IS :lol:

I've seen the work you did for stav and its great, ill speak to you more about it or you could make one and bring it to RSCS that would be better :thumbup:

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

Lexuspat

02-04-2019, 03:22 PM #18

[SIZE="2"]Click to visit my Project Thread or my Flickr Account[/SIZE]

OutlawJapClub Admin Team

sprinter2012
Posting Freak

2,484

02-04-2019, 03:23 PM

#19

Hurricane You still worried about the cradle, check what I made for stav, then ask me again if I can make what you need

I don't doubt that you are capable of making it, but wouldn't you need a cradle and/or charger to build it from?

That's the bit we're struggling on, as we have nothing but pictures to work from.

sprinter2012

02-04-2019, 03:23 PM #19

Hurricane You still worried about the cradle, check what I made for stav, then ask me again if I can make what you need

I don't doubt that you are capable of making it, but wouldn't you need a cradle and/or charger to build it from?

That's the bit we're struggling on, as we have nothing but pictures to work from.

sprinter2012
Posting Freak

2,484

12-04-2019, 09:05 AM

#20

I know I said I wasn't going to spend any money on this until I'd got the cradle sorted, but I couldn't resist this as they don't come up for sale very often...

[Image: DSC_0145.jpg]

sprinter2012

12-04-2019, 09:05 AM #20

I know I said I wasn't going to spend any money on this until I'd got the cradle sorted, but I couldn't resist this as they don't come up for sale very often...

[Image: DSC_0145.jpg]