Project: DIY Supercharger
Project: DIY Supercharger
this is and will continue to be the stumbling block for this build
![[Image: FB_IMG_1474048273787_zpsnbfq6a3s.jpg]](http://i1227.photobucket.com/albums/ee440/davis5835/Mobile%20Uploads/FB_IMG_1474048273787_zpsnbfq6a3s.jpg)
cornishlexus
14-02-2020, 02:18 PM #93do lexus sell it seperatley have you spoken to any one in lexus uk about sourcing one for you is maybe beta than asking a main dealer the part number for the cradle is AM27964
daveo do you know if a tte supercharger has same mountings as the eaton m62 as i might be able to measure one up.
Yes it does, I even have a broken supercharger at home to measure from.
Sent from my LT26i using Xparent Skyblue Tapatalk 2
sprinter2012
15-02-2020, 04:35 AM #95daveo do you know if a tte supercharger has same mountings as the eaton m62 as i might be able to measure one up.
Yes it does, I even have a broken supercharger at home to measure from.
Sent from my LT26i using Xparent Skyblue Tapatalk 2
im in the process of making another cradle,but its a slow process,
ill post some pics when its done,but dont hold yer breath.
on another note i still cant find the original pulley the tte kit used,i adapted a merc one,which is 138mm but others say one from the supra fits?
its like finding the holy grail haha.:presents2:
buzzard2011
15-02-2020, 05:00 AM #96the easy part is the measurements of the bolt holes,the not so easy part is getting the angles for the supporting legs,that bolt to the engine block and so forth,even with measurements you will still need to figure these angles out by fixing and adapting,until you've got it right.
im in the process of making another cradle,but its a slow process,
ill post some pics when its done,but dont hold yer breath.
on another note i still cant find the original pulley the tte kit used,i adapted a merc one,which is 138mm but others say one from the supra fits?
its like finding the holy grail haha.:presents2:
let us know when ya find it. yea there is no problem measuring the hole positions. ive an eaton there to measure up. as above its all about getting the angles rite. even having another cradle longside you , your still going to have issues with the angles all working intogether nicely.
in thinking a block bracket machined out of a big lump of ally rather than the bar cradle type.or then again using some item ally and making up a frame that way. might have a look into the weekend and see how it goes for me.
ha ha the holy grail !!!! let us know when ya find it.
yea there is no problem measuring the hole positions. ive an eaton there to measure up. as above its all about getting the angles rite. even having another cradle longside you , your still going to have issues with the angles all working intogether nicely.
in thinking a block bracket machined out of a big lump of ally rather than the bar cradle type.or then again using some item ally and making up a frame that way. might have a look into the weekend and see how it goes for me.
But my opinion, having looked into making a cradle, is that trying to make an exact copy of the TTE one is a waste of time and that you are better off just making your own design.
As long as the holes for the engine and charger are correct, what you put between them is irrelevant.
Sent from my LT26i using Xparent Skyblue Tapatalk 2
sprinter2012
16-02-2020, 03:27 AM #98I'm actually still in the process of acquiring a genuine TTE cradle.
But my opinion, having looked into making a cradle, is that trying to make an exact copy of the TTE one is a waste of time and that you are better off just making your own design.
As long as the holes for the engine and charger are correct, what you put between them is irrelevant.
Sent from my LT26i using Xparent Skyblue Tapatalk 2
its very easy to run a straight edge along the front of thr 2 pulleys to ensure squareness. i think people are makingt a bigger issue out of making this bracket than there is to it !! if you have an eye at all in your head and a vernier and the use of a cnc mill i think there wouldnt be too much to it.
i dont think you would shred belts if you had a block bracket with slightly elongated slots for adjustment. if your paranoyed about making a cradle and belts shredding id be asking someone else to make it far ya its very easy to run a straight edge along the front of thr 2 pulleys to ensure squareness. i think people are makingt a bigger issue out of making this bracket than there is to it !! if you have an eye at all in your head and a vernier and the use of a cnc mill i think there wouldnt be too much to it.
2 Guest(s)
2 Guest(s)
Views 489
Last Post by
Views 479
Last Post by
Views 207
Last Post by
Views 1,570
Last Post by
Views 378
Last Post by
Views 960
Last Post by
Views 690
Last Post by
Views 528
Last Post by
Views 638
Last Post by