Removing parts
Removing parts
That should have a loom going to the abs ecu. That can just be cut as they're only spliced in.
A loom to the main ecu for the injectors. This will need to be followed to the ecu as they intercept the injector wires so you'll need to join therm back together to get the car running again.
Then a loom to the controller.
If there's a second plug in the main unit then there's a final loom with the diagnostic plug and led on it as well.
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
17-02-2020, 12:17 AM #2It should have a main silver brain unit. You need to find that.
That should have a loom going to the abs ecu. That can just be cut as they're only spliced in.
A loom to the main ecu for the injectors. This will need to be followed to the ecu as they intercept the injector wires so you'll need to join therm back together to get the car running again.
Then a loom to the controller.
If there's a second plug in the main unit then there's a final loom with the diagnostic plug and led on it as well.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Anyway, back to the racelogic. I traced the controller wire back to the main brain of it
![[Image: racelogic001_zps43096b14.jpg]](http://i100.photobucket.com/albums/m29/gixxer500/Racelogic%20Removal/racelogic001_zps43096b14.jpg)
I then started to trace each of the wires coming out of that, and got to this
![[Image: racelogic002_zpsc11f6482.jpg]](http://i100.photobucket.com/albums/m29/gixxer500/Racelogic%20Removal/racelogic002_zpsc11f6482.jpg)
Now the wire hanging off the edge of the car is still connected but wanted to make sure I remove from the correct place. Anyway in the pic below the wire coming up from under my hand is the one I'm concerned about as it seems to be spliced into the wires going into the blue plug, but also seems to be spliced into the four thick grey wires coming from above.
![[Image: racelogic003_zps55844487.jpg]](http://i100.photobucket.com/albums/m29/gixxer500/Racelogic%20Removal/racelogic003_zps55844487.jpg)
![[Image: racelogic004_zpsbe13b729.jpg]](http://i100.photobucket.com/albums/m29/gixxer500/Racelogic%20Removal/racelogic004_zpsbe13b729.jpg)
![[Image: racelogic005_zpsd54e2f4c.jpg]](http://i100.photobucket.com/albums/m29/gixxer500/Racelogic%20Removal/racelogic005_zpsd54e2f4c.jpg)
Is that where I need to cut (blue/red/yellow/green wires) to finish removing it or is there still more to find??
Been trying to do a bit to the 300 this afternoon, got most of the racelogic out now, and also started on the sigma alarm system though I think thats going to be more than I can cope with after tracing some of the wires.
Anyway, back to the racelogic. I traced the controller wire back to the main brain of it
I then started to trace each of the wires coming out of that, and got to this
Now the wire hanging off the edge of the car is still connected but wanted to make sure I remove from the correct place. Anyway in the pic below the wire coming up from under my hand is the one I'm concerned about as it seems to be spliced into the wires going into the blue plug, but also seems to be spliced into the four thick grey wires coming from above.
Is that where I need to cut (blue/red/yellow/green wires) to finish removing it or is there still more to find??
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
18-02-2020, 07:14 AM #10Yeah cut there, they are the wires to the abs sensors.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
4 Guest(s)
4 Guest(s)
Views 851
Last Post by
Views 729
Last Post by
Views 1,030
Last Post by
Views 2,019
Last Post by
Views 1,210
Last Post by
Views 722
Last Post by