JapCarForum Car Manufacturers Lexus/Toyota IS200 / IS300 / SPORTCROSS / Altezza Workshop - Submit Your Tip! IS 200 Front Armrest Fitting Instructions

IS 200 Front Armrest Fitting Instructions

IS 200 Front Armrest Fitting Instructions

Moley
Posting Freak
Find
6,230
06-03-2017, 12:44 PM
#1
1. First you need to remove the old compartment lid. There are just two screws that hold this in place.
[Image: 004.jpg]

2. Then remove the felt base ( if you have one ) to reveal two screws, remove these.
[Image: 006.jpg]

3.Now remove the handbrake gator, pull it straight up there are two tabs that hold this in place ,but they will just pop out.
[Image: 007.jpg]

4. Now remove the ashtray.
[Image: 008.jpg]
[Image: 009.jpg]

5. Remove the panel that the ashtray sits in, and disconnect the cigarette lighter
[Image: 010.jpg]

6. Remove your gear knob , and remove the gear stick gator
[Image: 011.jpg]
[Image: 012.jpg]

7. Remove these two srews.
[Image: 013.jpg]

8.Remove these two screws from the center console, one either side
[Image: 014.jpg]

9.Now remove the center console , there are two tabs that hold this in place. The best way was just to give it a firm **** and they pop out.
[Image: 015.jpg]
[Image: 016.jpg]
This is what it looks like once removed and a good idea to give it a bit of a clean to remove the years of grime , and if you are lucky find some money.
[Image: 018.jpg]
[Image: 020.jpg]

10. Now with the center console removed , turn it upside down and remove the rear cup holders , you will need to push the two metal tabs inwards to achieve this.
[Image: 021.jpg]
[Image: 025.jpg]
and remove the steal housing
[Image: 023.jpg]

11. remove the other two screws and the old box will lift out.
[Image: 027.jpg]
it will look like this once removed.
[Image: 028.jpg]

12. Now fit your new box and replace the metal housing and rear cup holders .
[Image: 029.jpg]

13.Remove the bracket going over the handbrake cable with a 10mm socket , you will not need this bracket again.
[Image: 030.jpg]
[Image: 031.jpg]

14. Now its time to fit the new armrest tower , with the arrow pointing forwards. Bolt onto car using the bolts removed from the bracket for the handbrake cable
[Image: 032.jpg]
[Image: 033.jpg]
I decided to cut a piece of the carpet to make it sit better , but this is up to you if you want to do this or not.
[Image: 034.jpg]
I found doing this made it sit better.
[Image: 036.jpg]

15. Now refit the center console .
[Image: 037.jpg]

and replace all screws to hold in place.
[Image: 042.jpg]

16. Now fit the armrest hinge cover, making sure that the five tabs fit into place.
[Image: 038.jpg]
[Image: 039.jpg]

17. Time has come to fit the armrest to the hinge , there are two bolt for this and you need a 12mm socket
[Image: 040.jpg]
[Image: 041.jpg]

18. Next there are two caps to push onto the hinge to cover the bolts, these are marked left and right. You will also notice an arrow on the inside of the cap . This needs to be pointing straight up for them to fit correctly .
[Image: 044.jpg]
[Image: 046.jpg]

19. Only thing left to do is fit the piece of felt for the new compartment and fit the magnet hole cover
[Image: 043.jpg]
[Image: 047.jpg]
[Image: 048.jpg]

20. Stand back and admire your handy work
[Image: 049.jpg]
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
Reply
Reply
Moley
06-03-2017, 12:44 PM #1

1. First you need to remove the old compartment lid. There are just two screws that hold this in place.
[Image: 004.jpg]

2. Then remove the felt base ( if you have one ) to reveal two screws, remove these.
[Image: 006.jpg]

3.Now remove the handbrake gator, pull it straight up there are two tabs that hold this in place ,but they will just pop out.
[Image: 007.jpg]

4. Now remove the ashtray.
[Image: 008.jpg]
[Image: 009.jpg]

5. Remove the panel that the ashtray sits in, and disconnect the cigarette lighter
[Image: 010.jpg]

6. Remove your gear knob , and remove the gear stick gator
[Image: 011.jpg]
[Image: 012.jpg]

7. Remove these two srews.
[Image: 013.jpg]

8.Remove these two screws from the center console, one either side
[Image: 014.jpg]

9.Now remove the center console , there are two tabs that hold this in place. The best way was just to give it a firm **** and they pop out.
[Image: 015.jpg]
[Image: 016.jpg]
This is what it looks like once removed and a good idea to give it a bit of a clean to remove the years of grime , and if you are lucky find some money.
[Image: 018.jpg]
[Image: 020.jpg]

10. Now with the center console removed , turn it upside down and remove the rear cup holders , you will need to push the two metal tabs inwards to achieve this.
[Image: 021.jpg]
[Image: 025.jpg]
and remove the steal housing
[Image: 023.jpg]

11. remove the other two screws and the old box will lift out.
[Image: 027.jpg]
it will look like this once removed.
[Image: 028.jpg]

12. Now fit your new box and replace the metal housing and rear cup holders .
[Image: 029.jpg]

13.Remove the bracket going over the handbrake cable with a 10mm socket , you will not need this bracket again.
[Image: 030.jpg]
[Image: 031.jpg]

14. Now its time to fit the new armrest tower , with the arrow pointing forwards. Bolt onto car using the bolts removed from the bracket for the handbrake cable
[Image: 032.jpg]
[Image: 033.jpg]
I decided to cut a piece of the carpet to make it sit better , but this is up to you if you want to do this or not.
[Image: 034.jpg]
I found doing this made it sit better.
[Image: 036.jpg]

15. Now refit the center console .
[Image: 037.jpg]

and replace all screws to hold in place.
[Image: 042.jpg]

16. Now fit the armrest hinge cover, making sure that the five tabs fit into place.
[Image: 038.jpg]
[Image: 039.jpg]

17. Time has come to fit the armrest to the hinge , there are two bolt for this and you need a 12mm socket
[Image: 040.jpg]
[Image: 041.jpg]

18. Next there are two caps to push onto the hinge to cover the bolts, these are marked left and right. You will also notice an arrow on the inside of the cap . This needs to be pointing straight up for them to fit correctly .
[Image: 044.jpg]
[Image: 046.jpg]

19. Only thing left to do is fit the piece of felt for the new compartment and fit the magnet hole cover
[Image: 043.jpg]
[Image: 047.jpg]
[Image: 048.jpg]

20. Stand back and admire your handy work
[Image: 049.jpg]

Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice

Reply
Reply
Moley
Posting Freak
Find
6,230
02-02-2021, 11:40 PM
#2
For the attention of scudney
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
Reply
Reply
Moley
02-02-2021, 11:40 PM #2

For the attention of scudney

Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice

Reply
Reply
Recently Browsing
 1 Guest(s)
Recently Browsing
 1 Guest(s)
Related Threads…
Is200 Front Electric Seat Fitting
by Rabster
Replies 0
Views 179
13-12-2022, 05:57 AM
Last Post by Rabster
Fitting Fog Brake light conversion
by Sparkystav
Replies 11
Views 1,435
05-02-2022, 09:27 PM
Last Post by Sparkystav
Fitting the E-Manage Ultimate
by S
Replies 16
Views 917
23-01-2022, 08:43 AM
Last Post by JapHappyScott
Fitting Electrically Adjusted and heated Seats
by S
Replies 8
Views 550
25-02-2020, 01:37 AM
Last Post by el_bandido
Lexus IS200 How to change the front map light bulb!
by Bandit
Replies 15
Views 2,413
27-10-2018, 01:07 PM
Last Post by davidjamesbattersby
How To Recon A Front Caliper on a Lexus IS200
by ormi
Replies 16
Views 1,995
03-10-2018, 08:33 AM
Last Post by toxo
fitting led scuff plates
by jay_russell
Replies 13
Views 1,244
30-01-2018, 01:06 PM
Last Post by jay_russell
Hks fcd fitting for the is200
by Bandit
Replies 1
Views 799
23-01-2018, 07:18 AM
Last Post by Jambo
Back box fitting...
by ormi
Replies 7
Views 822
16-01-2018, 10:50 AM
Last Post by Sparkystav
Fitting reverse Dip Mirrors Passenger side
by Rabster
Replies 0
Views 738
10-01-2018, 09:03 AM
Last Post by Rabster