Little write up on the evolution of my car
Little write up on the evolution of my car
07-12-2016, 10:10 AM
Moley sorry but you are wrong. stainless the magnet just sticks ever so slightly and with aluminium it dose not stick atoll. Try it with a aluninium drinks can and you'll see :biggrin::biggrin:
Are you sure?:w00t: I doubt mate. have a look here.
http://answers.yahoo.com/question/index?...051AA0PxwH
try the magnet on some of your spanners. i doubt if it will stick. :thumbup:
LEXUS IS200 - The most fun car to go sideways
Moley sorry but you are wrong. stainless the magnet just sticks ever so slightly and with aluminium it dose not stick atoll. Try it with a aluninium drinks can and you'll see :biggrin::biggrin:
Are you sure?:w00t: I doubt mate. have a look here.
http://answers.yahoo.com/question/index?...051AA0PxwH
try the magnet on some of your spanners. i doubt if it will stick. :thumbup:
LEXUS IS200 - The most fun car to go sideways
21-12-2016, 12:15 PM
had a couple of times theyve scraped. most of the time just steep drives or uneven roads. but once or twice when ive been moving down country lanes in dips in the road. must have look good from the rear cause i bet it threw sparks up but not good for the confidence.
so gonna have a look under the car and see where their scraping and see if i can raise that bit up.
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
21-12-2016, 12:15 PM #192well the brace are fitted as you know.
had a couple of times theyve scraped. most of the time just steep drives or uneven roads. but once or twice when ive been moving down country lanes in dips in the road. must have look good from the rear cause i bet it threw sparks up but not good for the confidence.
so gonna have a look under the car and see where their scraping and see if i can raise that bit up.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
21-12-2016, 12:27 PM
![[Image: vht7pe.jpg]](http://i45.tinypic.com/vht7pe.jpg)
Notr: The braces shown in the pic are Cusco.
LEXUS IS200 - The most fun car to go sideways
How much does your braces extend from the car Stav? From this pic that i found they do not seem to extend a lot. The front under brace seems to be me a perfect replacement of the OEM. It doesn't extend at all.
Notr: The braces shown in the pic are Cusco.
LEXUS IS200 - The most fun car to go sideways
21-12-2016, 12:34 PM
the rear however isnt.
the cusco ones are quite thin and are only a square.
The japsai ones are made of 7-8mm thick bar and have bits that go diagonally across. these bits are welded on top of the square bit so they stick down even further,
Gonna drop them off again and get them remade flat, then hope they fit.
see here:
shows how thick they are (infact you can see some other just to the left, they look the same as the cusco ones, so you can compare the thickness)
![[Image: rear_braces_made_up.sized.jpg]](http://www.lexusownersclub.com/gallery/albums/Misc/rear_braces_made_up.sized.jpg)
and fitted
![[Image: rearbrace_fitted_1.sized.jpg]](http://www.lexusownersclub.com/gallery/albums/Misc/rearbrace_fitted_1.sized.jpg)
Edited 01-02-2010, 10:10 PM by Sparkystav.
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
21-12-2016, 12:34 PM #195The front ones fine.
the rear however isnt.
the cusco ones are quite thin and are only a square.
The japsai ones are made of 7-8mm thick bar and have bits that go diagonally across. these bits are welded on top of the square bit so they stick down even further,
Gonna drop them off again and get them remade flat, then hope they fit.
see here:
shows how thick they are (infact you can see some other just to the left, they look the same as the cusco ones, so you can compare the thickness)
and fitted
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
21-12-2016, 12:39 PM
Sparkystav The front ones fine.
the rear however isnt.
the cusco ones are quite thin and are only a square.
The japsai ones are made of 7-8mm thick bar and have bits that go diagonally across. these bits are welded on top of the square bit so they stick down even further,
Gonna drop them off again and get them remade flat, then hope they fit.
see here:
shows how thick they are (infact you can see some other just to the left, they look the same as the cusco ones, so you can compare the thickness)
and fitted
You have a point there Stav. I did not know that the Japsai are constructed from thick bars and as i can see from the pics they extend much more in compare with Cusco braces. :blink:
LEXUS IS200 - The most fun car to go sideways
Sparkystav The front ones fine.
the rear however isnt.
the cusco ones are quite thin and are only a square.
The japsai ones are made of 7-8mm thick bar and have bits that go diagonally across. these bits are welded on top of the square bit so they stick down even further,
Gonna drop them off again and get them remade flat, then hope they fit.
see here:
shows how thick they are (infact you can see some other just to the left, they look the same as the cusco ones, so you can compare the thickness)
and fitted
You have a point there Stav. I did not know that the Japsai are constructed from thick bars and as i can see from the pics they extend much more in compare with Cusco braces. :blink:
LEXUS IS200 - The most fun car to go sideways
21-12-2016, 12:42 PM
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
21-12-2016, 12:42 PM #197I think the red thin ones to the side are TOMS ones,cause i dont think the cusco ones have the "X" piece
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
21-12-2016, 12:45 PM
![[Image: ormiedit1-2.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/ormiedit1-2.jpg)
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
stav see the bars you have are you just going to use them as a template to make new flat ones?or you going to cut them up??
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
21-12-2016, 12:49 PM
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
21-12-2016, 12:49 PM #199Prob cut them up mate
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
21-12-2016, 12:52 PM
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
nooooooooooo :crying: cant the metal wizzard moley take mesurements??then you wont have to cut them up??then i can buy it off you??:thumbup1::lol:
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Recently Browsing
6 Guest(s)
6 Guest(s)
Recently Browsing
6 Guest(s)
6 Guest(s)
Related Threads…
Replies 2
Views 283
Views 283
22-02-2024, 02:07 PM
Last Post bySparkystav
Last Post by