Great Project
Great Project
http://toyotaperformancemagazine.com/for...-V6-engine
Take a look at this project you could have a lighting quick car...
http://toyotaperformancemagazine.com/for...-V6-engine
For Sale: My 5VZ-FE Turbo V6 engine
For sale here is the rear clip that was in my MR2 V6 Turbo, sadly now resting in piece.
Everything that you will need to get your MR2 with my old setup, excluding a Cinquecento radiator
Included are:
1. Fully built 5VZ-FE, with Arias pistons and rings. Pauter rods, ProFlow oversized valves, Stage 2 Sea2Sky 262 duration cams, 6x 1000cc injectors, resistor pack from a MkIV Supra (bought new). New coil packs for the for wasted spark ignition.
2. Syvecs S6 GP ECU (with boost control, active knock, traction/launch control)
3. Garrett GT4094R
4. TiAL F46 Wastegate with 0.7bar spring
5. Custom Chargecooler core and associated piping
6. MR2 Revision 3 Gearbox in excellent condition, no notches, good shift, no crunches with RPS Max Puk clutch, to take 525lb/ft
You will need to make sure your fuel pump is up to the job and the fuel lines.
Everything above has less than 1000 miles on the clock.
Woodsport can drop this in for you (price to be negotiated between you and Woodsport) - but once installed and fired up, you're on for 420bhp @ 0.7bar
The engine was $12000, shipped to the UK from USA. ECU is £1250+VAT (exc harness and mapping). Turbo was £1000, wastegate was £300, etc, etc.
Bear in mind, once installed, and the boost is turned up by Ryan, there's not going to be much this side of £100,000+ cars that will touch you.
If you want to put this in another car, it would be awesome and more than likely a world-first (if you're in the UK, speak to Woodsport about whatever car you have for this engine).
If it's going in to an MR2, you'd be best buying the whole rear drive train - £7000
For any other car - please comment!
I have some longer gear ratios that I can throw in to the sale and some braided fuel hoses and filter. For MR2's the Carbon End-Can exhaust system will be included as part of the sale.
Hope this goes to a good home, as it has the potential to be stunningly quick in whatever you put it in.
If interested go to Toyota performance magazine website
For Sale: My 5VZ-FE Turbo V6 engine
For sale here is the rear clip that was in my MR2 V6 Turbo, sadly now resting in piece.
Everything that you will need to get your MR2 with my old setup, excluding a Cinquecento radiator
Included are:
1. Fully built 5VZ-FE, with Arias pistons and rings. Pauter rods, ProFlow oversized valves, Stage 2 Sea2Sky 262 duration cams, 6x 1000cc injectors, resistor pack from a MkIV Supra (bought new). New coil packs for the for wasted spark ignition.
2. Syvecs S6 GP ECU (with boost control, active knock, traction/launch control)
3. Garrett GT4094R
4. TiAL F46 Wastegate with 0.7bar spring
5. Custom Chargecooler core and associated piping
6. MR2 Revision 3 Gearbox in excellent condition, no notches, good shift, no crunches with RPS Max Puk clutch, to take 525lb/ft
You will need to make sure your fuel pump is up to the job and the fuel lines.
Everything above has less than 1000 miles on the clock.
Woodsport can drop this in for you (price to be negotiated between you and Woodsport) - but once installed and fired up, you're on for 420bhp @ 0.7bar
The engine was $12000, shipped to the UK from USA. ECU is £1250+VAT (exc harness and mapping). Turbo was £1000, wastegate was £300, etc, etc.
Bear in mind, once installed, and the boost is turned up by Ryan, there's not going to be much this side of £100,000+ cars that will touch you.
If you want to put this in another car, it would be awesome and more than likely a world-first (if you're in the UK, speak to Woodsport about whatever car you have for this engine).
If it's going in to an MR2, you'd be best buying the whole rear drive train - £7000
For any other car - please comment!
I have some longer gear ratios that I can throw in to the sale and some braided fuel hoses and filter. For MR2's the Carbon End-Can exhaust system will be included as part of the sale.
Hope this goes to a good home, as it has the potential to be stunningly quick in whatever you put it in.
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
13-05-2017, 08:17 AM #53.4L V6 Turbo conversion!
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
13-05-2017, 10:25 AM #8Its been for sale a long time on IMOC............... Its not an easy conversion on the MR2, may as well build a forged 3SGTE and then you have that power and possibly more.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
Johnny@TPM
13-05-2017, 01:04 PM #9Hi guys - that's my build 
It made 420bhp @ 0.7bar and 430lb/ft, from 2400rpm 
2tongues Its been for sale a long time on IMOC............... Its not an easy conversion on the MR2, may as well build a forged 3SGTE and then you have that power and possibly more.
If you were to buy the rear clip - you'd just need a cinquecento rad and a hole cut in the rear firewall for the CC pipes and you can lift it all in, effectively in situ. The hardwork in the fabrication of the pipes and placements has already been done.
Makes it a lot easier than a virgin install.
Johnny@TPM
17-05-2017, 03:46 AM #102tongues Its been for sale a long time on IMOC............... Its not an easy conversion on the MR2, may as well build a forged 3SGTE and then you have that power and possibly more.
If you were to buy the rear clip - you'd just need a cinquecento rad and a hole cut in the rear firewall for the CC pipes and you can lift it all in, effectively in situ. The hardwork in the fabrication of the pipes and placements has already been done.
Makes it a lot easier than a virgin install.
1 Guest(s)
1 Guest(s)
Views 508
Last Post by
Views 292
Last Post by
Views 264
Last Post by
Views 1,935
Last Post by
Views 615
Last Post by
Views 548
Last Post by
Views 771
Last Post by
Views 299
Last Post by
Views 432
Last Post by