Custom build exhaust
Custom build exhaust
Forgive my bad english...
I had my is200 over 2 years with an aftermarket exhaust (catalyst, rear and middle silencer) but i never liked the sound.
It had too bass tone and was more loud than i would like. The silk sound of the inline 6 engine was all covered and i wanted a more destinguished sound for my car.
So one weekend me and my brother began to build our own exhaust.
Basically we didn't expect the result to be satisfying but we wanted to try.
Here we go:
We had some stainless steel tubes about the same diameter as the stock pipes on car.
First thing to make the piece inside the muffler perforated:
![[Image: IMAG0170.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0170.jpg)
Next to make the body of the muffler out of a stainless steel sheet that i bought:
![[Image: IMAG0171.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0171.jpg)
![[Image: IMAG0177.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0177.jpg)
![[Image: IMAG0175.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0175.jpg)
![[Image: IMAG0174.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0174.jpg)
We used stainless steel wire mesh around the perforated tube and then fiberglass
![[Image: IMAG0182.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0182.jpg)
Muffler closed and tested the position that it will sit under the car
![[Image: IMAG0186.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0186.jpg)
Then we cut the pipe behind the old muffler and tested the new one to see about what kind of sound we ve got..
The results was not very good. There was a lot of sound reduce but low frequencies were still too much.
So we decided to go the way the HKS silent went.
This muffler uses an separate enclosure as a resonator for the low frequencies.
So, here it is
![[Image: IMAG0190.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0190.jpg)
![[Image: IMAG0189.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0189.jpg)
![[Image: IMAG0192.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0192.jpg)
![[Image: IMAG0196.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0196.jpg)
![[Image: IMAG0197.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0197.jpg)
![[Image: IMAG0199.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0199.jpg)
![[Image: IMAG0206.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0206.jpg)
![[Image: IMAG0207.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0207.jpg)
![[Image: IMAG0208.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0208.jpg)
DimitrisTS
17-06-2017, 01:31 AM #1This is my first post here so i want to say a hello to everyone!
Forgive my bad english...
I had my is200 over 2 years with an aftermarket exhaust (catalyst, rear and middle silencer) but i never liked the sound.
It had too bass tone and was more loud than i would like. The silk sound of the inline 6 engine was all covered and i wanted a more destinguished sound for my car.
So one weekend me and my brother began to build our own exhaust.
Basically we didn't expect the result to be satisfying but we wanted to try.
Here we go:
We had some stainless steel tubes about the same diameter as the stock pipes on car.
First thing to make the piece inside the muffler perforated:
Next to make the body of the muffler out of a stainless steel sheet that i bought:
We used stainless steel wire mesh around the perforated tube and then fiberglass
Muffler closed and tested the position that it will sit under the car
Then we cut the pipe behind the old muffler and tested the new one to see about what kind of sound we ve got..
The results was not very good. There was a lot of sound reduce but low frequencies were still too much.
So we decided to go the way the HKS silent went.
This muffler uses an separate enclosure as a resonator for the low frequencies.
So, here it is
The car run very quiet. Almost as stock!
That extra resonator does A LOT of work at cutting down the low frequencies!
So we decided to remove the middle box and see what happens:
![[Image: IMAG0217.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0217.jpg)
And the result was... exactly as i wanted !!
Sound seemed balanced between the engine and muffler.
Of course we had to test it later on road with some load on the engine to see exactly what we had.
Next step to make a nice muffler tip.
![[Image: IMAG0210.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0210.jpg)
![[Image: IMAG0211.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0211.jpg)
![[Image: IMAG0212.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0212.jpg)
![[Image: IMAG0213.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0213.jpg)
![[Image: IMAG0214.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0214.jpg)
Then some testing on the car and final welding:
![[Image: IMAG0215.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0215.jpg)
![[Image: IMAG0219.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0219.jpg)
![[Image: IMAG0220.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0220.jpg)
A little polishing to give a decent look
![[Image: IMAG0221.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0221.jpg)
![[Image: IMAG0222.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/IMAG0222.jpg)
And testing on road!
Have to say i am 100% happy with the result.
I don't know how much before the fiberglass begin to fade, but after a year or two i can replace it.
It cost me about 40 pounds and a lot of work.
Please allow me to say from here a big thank you to my brother that did most of the work!
![[Image: DSC_0102_3_4_tonemapped-wall.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/DSC_0102_3_4_tonemapped-wall.jpg)
![[Image: DSC_0096_7_8_tonemapped.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/eksatmisi/DSC_0096_7_8_tonemapped.jpg)
DimitrisTS
17-06-2017, 01:32 AM #2After testing on car, i have to say that i was very suprized!
The car run very quiet. Almost as stock!
That extra resonator does A LOT of work at cutting down the low frequencies!
So we decided to remove the middle box and see what happens:
And the result was... exactly as i wanted !!
Sound seemed balanced between the engine and muffler.
Of course we had to test it later on road with some load on the engine to see exactly what we had.
Next step to make a nice muffler tip.
Then some testing on the car and final welding:
A little polishing to give a decent look
And testing on road!
Have to say i am 100% happy with the result.
I don't know how much before the fiberglass begin to fade, but after a year or two i can replace it.
It cost me about 40 pounds and a lot of work.
Please allow me to say from here a big thank you to my brother that did most of the work!
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
17-06-2017, 01:56 AM #3Top work mate, i could never do that sort of fabrication by myself!
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R
Seems like a lot of work but actually looks really good, nice one!
Tinted Glass-Sports Grill-Debadged-TTE Spoiler-TTE Lowering Springs-PLUK Kazama Exhaust-18" Aero Alloys-K&N Air Filter-Denso Iridium Power Spark Plugs-Quad Tail Light Conversion-6000K HID-X-White High Beam-6 LED Sidelights-Quad LED Boot Light-JDM OEM Smoked Front Fogs-JDM Blue Reverse Bulbs-LS430 Smoked Side Repeaters-6 LED Side Repeaters-Chrome Indicator Bulbs-Alpine HU-Rear Headrest Monitors-PIAA Super Sporza-Fan Washer Jets-Lex Tax Disc Holder-Chrome Gear Knob-2003 Cup Holder-Toyo Proxes T1-R
Other things i ve done is a car pc installation.
I got from australia a used oem screen case and i put inside a 7" lcd touchscreen.
So i have video - music - tv - obd data - gps navigation - wifi - etc in my car.
![[Image: LexusCarPC-5.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/LexusCarPC-5.jpg)
![[Image: LexusCarPC-8.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/LexusCarPC-8.jpg)
Also when i got this car, the dashboard had a lot of scratches.
I took it out, sand it, paint it and reinstall it. That was a lot of work also...
![[Image: ksilomeno2-6.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/ksilomeno2-6.jpg)
![[Image: xartomeno-9.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/xartomeno-9.jpg)
But the result was very satisfactory
![[Image: teleiomeno-7.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/teleiomeno-7.jpg)
oh yes. i also did the boot mode, that opens fully by it self, the fog-brake-tail lights mod and painted my calipers black with lexus decals
I really love this car!!
here is another photo of it that i like:
![[Image: DSC_0055.jpg]](http://i472.photobucket.com/albums/rr82/DimitrisTS/DSC_0055.jpg)
My next mod is to make a short shift.
I know i can do it well, but there is always the possibility something to go wrong..
So, is anyone here, that have a spare oem shift lever to sell?
DimitrisTS
17-06-2017, 04:30 AM #7Thank you all for your kind comments..!
Other things i ve done is a car pc installation.
I got from australia a used oem screen case and i put inside a 7" lcd touchscreen.
So i have video - music - tv - obd data - gps navigation - wifi - etc in my car.
Also when i got this car, the dashboard had a lot of scratches.
I took it out, sand it, paint it and reinstall it. That was a lot of work also...
But the result was very satisfactory
oh yes. i also did the boot mode, that opens fully by it self, the fog-brake-tail lights mod and painted my calipers black with lexus decals
I really love this car!!
here is another photo of it that i like:
My next mod is to make a short shift.
I know i can do it well, but there is always the possibility something to go wrong..
So, is anyone here, that have a spare oem shift lever to sell?
Would not know where to start building my own exhaust
BHP, TORQUE, UNDER STEER, OVERSTEER FOR DUMMYS
BHP- how fast you hit the wall, TORQUE- how far you push the wall
OVER STEER- Dont see the wall, UNDER STEER- You do see it
1999 Blue IS200 SportTRD kit, K&N Filter
garyskisplym
17-06-2017, 04:35 AM #8Very nice work there.
Would not know where to start building my own exhaust
BHP, TORQUE, UNDER STEER, OVERSTEER FOR DUMMYS
BHP- how fast you hit the wall, TORQUE- how far you push the wall
OVER STEER- Dont see the wall, UNDER STEER- You do see it
1999 Blue IS200 SportTRD kit, K&N Filter
DimitrisTS My next mod is to make a short shift.
I know i can do it well, but there is always the possibility something to go wrong..
So, is anyone here, that have a spare oem shift lever to sell?
I do, lets be honest my cars not going back to standard, i'll dig it out for you
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
17-06-2017, 05:03 AM #9DimitrisTS My next mod is to make a short shift.
I know i can do it well, but there is always the possibility something to go wrong..
So, is anyone here, that have a spare oem shift lever to sell?
I do, lets be honest my cars not going back to standard, i'll dig it out for you
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav I do, lets be honest my cars not going back to standard, i'll dig it out for you
Thank you very much mate!
Please send me a message about it. Do you have a paypal account?
BTW i see you have a blue monster IS !! very nice!
DimitrisTS
17-06-2017, 05:23 AM #10Sparkystav I do, lets be honest my cars not going back to standard, i'll dig it out for you
Thank you very much mate!
Please send me a message about it. Do you have a paypal account?
BTW i see you have a blue monster IS !! very nice!
2 Guest(s)
2 Guest(s)
Views 473
Last Post by
Views 668
Last Post by
Views 2,028
Last Post by
Views 571
Last Post by
Views 953
Last Post by
Views 269
Last Post by