lexus is200 sat nav bypass cable
lexus is200 sat nav bypass cable
timmurray85
31-08-2019, 01:02 PM #11No worries dude, thanks for your reply! I might pop into maplins tomorrow and see if I can get the components! If I were to show this diagram to someone who knew about electronics should they be able to assemble it? Cheers mate!
timmurray85
01-09-2019, 03:27 AM #14I reckon you should, there are so many is owner's that would snap your hand off for one! Whack a few on eBay for a tenner and you'll be laughing! Has anyone got a picture of one they have made that I can use for reference when making mine? I'm gonna grab the components after work so hopefully can get this done at the weekend!
I don't have any pics I'm afraid, but that wouldn't have helped as they were heat shrinked and taped anyway.
I'll probably knock a few up again at some point, as there is always demand and I've got loads of the components for them at home.
speedfreek
01-09-2019, 07:06 AM #15A tenner! I sold mine for a fiver, and I thought I was taking the pee then!
I don't have any pics I'm afraid, but that wouldn't have helped as they were heat shrinked and taped anyway.
I'll probably knock a few up again at some point, as there is always demand and I've got loads of the components for them at home.
[SIZE=3]'93 Mazda Eunos Roadster Turbo[/SIZE]
(Current project)
timmurray85
01-09-2019, 07:12 AM #16Just been into maplin and the guy said he needs a data sheet so he knows which diodes/resistors etc to sell me??? I am well out of my depth here! Also, do all the components get soldered directly to a curcuit board or is it just going to be wires? Considering the beatsonic lead is about £130 I reckon you were undercutting yourself at a fiver!
PM me your address and I'll send you the components as I should have some hanging around somewhere.
I just creatively soldered them together to make a smaller unit as possible. Putting them onto a board is the most professional solution sure, but I didn't want bulk.
speedfreek
01-09-2019, 09:43 AM #17The components cost around £2, it's not about undercutting, it's helping out your mate
PM me your address and I'll send you the components as I should have some hanging around somewhere.
I just creatively soldered them together to make a smaller unit as possible. Putting them onto a board is the most professional solution sure, but I didn't want bulk.
[SIZE=3]'93 Mazda Eunos Roadster Turbo[/SIZE]
(Current project)
timmurray85
01-09-2019, 09:58 AM #18Are you sure mate? If you reply with your PayPal email I can reimburse you the cost of components and.postage! I did see this on another forum.. http://my.is/forums/f103/stock-nav-after...lp-408581/ is that ideally what I need to do?
timmurray85 Are you sure mate? If you reply with your PayPal email I can reimburse you the cost of components and.postage! I did see this on another forum.. http://my.is/forums/f103/stock-nav-after...lp-408581/ is that ideally what I need to do?
Not really no. The kit I make has 2 diodes and 3 resistors and a bit of wire. Looks much neater and much easier to make.
The diagram I posted up is what you need to make
speedfreek
01-09-2019, 11:53 AM #19timmurray85 Are you sure mate? If you reply with your PayPal email I can reimburse you the cost of components and.postage! I did see this on another forum.. http://my.is/forums/f103/stock-nav-after...lp-408581/ is that ideally what I need to do?
Not really no. The kit I make has 2 diodes and 3 resistors and a bit of wire. Looks much neater and much easier to make.
The diagram I posted up is what you need to make
[SIZE=3]'93 Mazda Eunos Roadster Turbo[/SIZE]
(Current project)
timmurray85
01-09-2019, 12:14 PM #20Cool, ill scrap that then! I'll let you know once I've done it and I'll take step by step pictures to help any other noobs who may need it
1 Guest(s)
1 Guest(s)
Views 7,471
Last Post by
Views 1,791
Last Post by
Views 942
Last Post by
Views 659
Last Post by
Views 19,260
Last Post by
Views 1,389
Last Post by
Views 717
Last Post by