fitting led scuff plates
fitting led scuff plates
I take no responsibility for any damage you may do to your car so please take your time and check everything is working and correct. This is just to help you fit them and may not be 100% correct.
Tools needed for this are
Multi meter
Phillips screwdriver and flat screwdriver
Cordless screwdriver
Solider iron or cable clamps and crimpers
3 m duel wire. Red / black
Silver ( gaffa) tape
Ok so you have your plates and screws for them and you’ve got you 2 led panels and 2 inverters and all the tools you need.
First thing to do is remove the old scuff plates sitting on the car, these are held in place with some poppers under the sill plate. If you take a flat screwdriver and slide it under (be careful not to scratch you paint) you will find the poppers holding the plate in place and you just need to lift them up a bit till the come away.
Cleaning the surface so the is no dirt trapped under the new plates.
So take your plate and turn it over and you will see the channel cut out for the panel.
![[Image: SDC11840.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/SDC11840.jpg)
Here you will fix your led panel in place with some gaffa tape to hold it in place.
Then you need to put it in the right place in the door so you cover the holes and it sits square.
![[Image: IMAG0070.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/IMAG0070.jpg)
Next you will need to fix the plates in place. The screws you have are self tapping screws so all you need to do id drill them in.
Next you will need to remove the cover strip along the door. This just pops off so flat screwdriver in the corner and lift it up.
![[Image: pic5.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/pic5.jpg)
Now you need to fix the wires for this over the rubber door seal and the passenger side can be hidden under the seat and the drivers side can be hidden in the fuse box in the corner.
Next is to remove the instrument gauge cover. Here there are 3 screws
![[Image: pic1.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/led%20plates/pic1.jpg)
There is one more at the bottom of the plastic to remove.
Next is to remove the cover. This is held in place with a few clips that just hold it in place.
![[Image: pic2.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/led%20plates/pic2.jpg)
And then you will need to disconnect the switches on the cover
![[Image: pic3.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/led%20plates/pic3.jpg)
And now you should have something like this.
![[Image: pic4.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/led%20plates/pic4.jpg)
Now you need to disconnect the battery for the next part.
You will see you key barrel and holding the plastic in place are 2 screws. Remove the screw and the light ring should come of. This is the wires you need to connect into. You will need to run cables to both sides for the inverters. After you have done this you need to feed the wires all the way through the dash and down to the inverters. Then the last bit to do is connect the wires up. Making sure you get them the right way around. You can check the with a meter to make sure they are right.
Then connect the battery back and check they both work when the door is open.
If all is working the last thing is to put the car back together and enjoy
jay_russell
22-09-2017, 10:41 AM #1LED SCUFF PLATES HOW TO
I take no responsibility for any damage you may do to your car so please take your time and check everything is working and correct. This is just to help you fit them and may not be 100% correct.
Tools needed for this are
Multi meter
Phillips screwdriver and flat screwdriver
Cordless screwdriver
Solider iron or cable clamps and crimpers
3 m duel wire. Red / black
Silver ( gaffa) tape
Ok so you have your plates and screws for them and you’ve got you 2 led panels and 2 inverters and all the tools you need.
First thing to do is remove the old scuff plates sitting on the car, these are held in place with some poppers under the sill plate. If you take a flat screwdriver and slide it under (be careful not to scratch you paint) you will find the poppers holding the plate in place and you just need to lift them up a bit till the come away.
Cleaning the surface so the is no dirt trapped under the new plates.
So take your plate and turn it over and you will see the channel cut out for the panel.
Here you will fix your led panel in place with some gaffa tape to hold it in place.
Then you need to put it in the right place in the door so you cover the holes and it sits square.
Next you will need to fix the plates in place. The screws you have are self tapping screws so all you need to do id drill them in.
Next you will need to remove the cover strip along the door. This just pops off so flat screwdriver in the corner and lift it up.
Now you need to fix the wires for this over the rubber door seal and the passenger side can be hidden under the seat and the drivers side can be hidden in the fuse box in the corner.
Next is to remove the instrument gauge cover. Here there are 3 screws
There is one more at the bottom of the plastic to remove.
Next is to remove the cover. This is held in place with a few clips that just hold it in place.
And then you will need to disconnect the switches on the cover
And now you should have something like this.
Now you need to disconnect the battery for the next part.
You will see you key barrel and holding the plastic in place are 2 screws. Remove the screw and the light ring should come of. This is the wires you need to connect into. You will need to run cables to both sides for the inverters. After you have done this you need to feed the wires all the way through the dash and down to the inverters. Then the last bit to do is connect the wires up. Making sure you get them the right way around. You can check the with a meter to make sure they are right.
Then connect the battery back and check they both work when the door is open.
If all is working the last thing is to put the car back together and enjoy
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
22-09-2017, 10:59 AM #2Good write up mate
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
is300_dino
22-09-2017, 03:59 PM #5do we need to inline fuse the strips?
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
i started by ordering some M4 rubber nut grommets
![[Image: 23a7a82c.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/23a7a82c.jpg)
![[Image: 6cafce7d.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/6cafce7d.jpg)
then i removed the existing door sill
![[Image: e4f56d50.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/e4f56d50.jpg)
once i removed the door sill i cleaned up the paint work
![[Image: a0b44265.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/a0b44265.jpg)
then i inserted the M4 Rubber Nut bugs
![[Image: fe14cbe0.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/fe14cbe0.jpg)
![[Image: 9a6908fa.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/9a6908fa.jpg)
with the rubber bungs in place i then positioned the sills and did the screws up
![[Image: 7b931888.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/7b931888.jpg)
![[Image: fd1ccd3c.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/fd1ccd3c.jpg)
i then followed jays instructions on fitting the transformer and wiring it in
very very easy to fit, well worth the money
Ok so here we go
i started by ordering some M4 rubber nut grommets
then i removed the existing door sill
once i removed the door sill i cleaned up the paint work
then i inserted the M4 Rubber Nut bugs
with the rubber bungs in place i then positioned the sills and did the screws up
i then followed jays instructions on fitting the transformer and wiring it in
very very easy to fit, well worth the money
![[Image: 6e63944a.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/6e63944a.jpg)
![[Image: 4a49b4ae.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/4a49b4ae.jpg)
![[Image: 953428f6.jpg]](http://i332.photobucket.com/albums/m330/Rabster_2008/Lexus%20Sill%20Plates/953428f6.jpg)
2002 '02' IS200 SE Auto - DVD Satnav with Voice Activation - [COLOR="Blue"]Strathcaron Blue - Parking Sensors - 5000K HIDs with Anti-Glare Bulbs - PIAA 6500K Main Beams - LED Sidelights - Mirror/Sunroof Closure - TTE Styling Kit - 18" Styling Kit Alloys with nitrogen filled Goodyear Eagle F1 Asymmetric Tyres - Bluetouch Multimedia Kit - Gromaudio AUX in - Black painted calipers with silver Lexus decals - 12 LED Dome Light - 96 LED Boot Light - Stainless Steel Sport Sill Plates - PIAA Silicone Wipers[/COLOR]
That looks great, could you use dome nuts as well to fix the plates down or would they be too big?
2002 '02' IS200 SE Auto - DVD Satnav with Voice Activation - [COLOR="Blue"]Strathcaron Blue - Parking Sensors - 5000K HIDs with Anti-Glare Bulbs - PIAA 6500K Main Beams - LED Sidelights - Mirror/Sunroof Closure - TTE Styling Kit - 18" Styling Kit Alloys with nitrogen filled Goodyear Eagle F1 Asymmetric Tyres - Bluetouch Multimedia Kit - Gromaudio AUX in - Black painted calipers with silver Lexus decals - 12 LED Dome Light - 96 LED Boot Light - Stainless Steel Sport Sill Plates - PIAA Silicone Wipers[/COLOR]
1 Guest(s)
1 Guest(s)
Views 188
Last Post by
Views 1,476
Last Post by
Views 970
Last Post by
Views 1,043
Last Post by
Views 586
Last Post by
Views 743
Last Post by
Views 767
Last Post by