window control led change
window control led change
so i went down to the car with a couple of screw drivers and a volt meter and took a look. we the first thing was to pop out the window unit and remove to back plate. took a volt meter and checked what the + and - were. after this i went home and warmed up the soildering iron . went to find the led units i have brought for this and no were to be found. so looking a bit harder at the unit i found out that you dont need these tiny little leds but can use t5 leds in there place. there is a bit of space to fit them in and after removing the orange ones i had a go at putting them in. found out that i had to trip the membrain plastic so the lamps could sit it the right place. all good. popped it back in the car and well it was good. will do a little write up and photo's soon.
also did the cig lighter and ashtray bulbs
jay_russell
27-10-2017, 08:56 AM #1well today i was off work and have been meaning to do this for a while now.
so i went down to the car with a couple of screw drivers and a volt meter and took a look. we the first thing was to pop out the window unit and remove to back plate. took a volt meter and checked what the + and - were. after this i went home and warmed up the soildering iron . went to find the led units i have brought for this and no were to be found. so looking a bit harder at the unit i found out that you dont need these tiny little leds but can use t5 leds in there place. there is a bit of space to fit them in and after removing the orange ones i had a go at putting them in. found out that i had to trip the membrain plastic so the lamps could sit it the right place. all good. popped it back in the car and well it was good. will do a little write up and photo's soon.
also did the cig lighter and ashtray bulbs
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
27-10-2017, 09:14 AM #2Sounds good mate, ive changed them for SMD's but their not the brightest
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
jay_russell
27-10-2017, 10:00 AM #3yer i was going to use smd aswell. i have 10 here but cant find them. but will post up some pics of how bright they are. same with the heater controls. they worked well
did my heater controls but want to do the heasted seat and trc buttons and ciggerette lighter aswel
![[Image: FB_IMG_1474048273787_zpsnbfq6a3s.jpg]](http://i1227.photobucket.com/albums/ee440/davis5835/Mobile%20Uploads/FB_IMG_1474048273787_zpsnbfq6a3s.jpg)
mate u have to do a right up for this as i want to do it but not that good at soldering
did my heater controls but want to do the heasted seat and trc buttons and ciggerette lighter aswel
jay_russell
27-10-2017, 11:12 PM #5nor am i but it's not that hard. will look into doing a write up on the heated seats aswell. we have the rest all covered
![[Image: IMG_0184.jpg]](http://i915.photobucket.com/albums/ac351/jay_russell_71/IMG_0184.jpg)
but must say i do like
1 Guest(s)
1 Guest(s)
Views 1,293
Last Post by
Views 1,243
Last Post by
Views 966
Last Post by
Views 784
Last Post by
Views 1,074
Last Post by
Views 683
Last Post by