JapCarForum Car Manufacturers Lexus/Toyota IS200 / IS300 / SPORTCROSS / Altezza supercharged is200 you might want to look at this

supercharged is200 you might want to look at this

supercharged is200 you might want to look at this

Pages (6): Previous 1 2 3 4 5 6 Next
Bandit
Posting Freak
6,464
12-07-2018, 11:35 AM
#31
ormi what oil have you got matey?what did you do to fix yours?

The oil Rabster used was the Castol Driveline syntrax universal, 75W-90 :biggrin:

Not done much to it mate, but when i had it off to polish it, i polished the intake port inside, just to get rid off some of the rough edges? and cleaned out the charger inside which surprisingly had loads of black gunk inside, just used a good cleaner to spray inside and then rinsed it out making it look like new again? runs so much smoother and made quite a bit of difference to it for some reason? :thumbup:

Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!
Bandit
12-07-2018, 11:35 AM #31

ormi what oil have you got matey?what did you do to fix yours?

The oil Rabster used was the Castol Driveline syntrax universal, 75W-90 :biggrin:

Not done much to it mate, but when i had it off to polish it, i polished the intake port inside, just to get rid off some of the rough edges? and cleaned out the charger inside which surprisingly had loads of black gunk inside, just used a good cleaner to spray inside and then rinsed it out making it look like new again? runs so much smoother and made quite a bit of difference to it for some reason? :thumbup:


Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!

ormi
Posting Freak
3,006
12-07-2018, 12:08 PM
#32
so did you split the charger?did you use a file follower by paper to polish the intake?
Edited 23-08-2011, 09:43 PM by ormi.

[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
ormi
12-07-2018, 12:08 PM #32

so did you split the charger?did you use a file follower by paper to polish the intake?


[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more

Bandit
Posting Freak
6,464
12-07-2018, 08:42 PM
#33
ormi so did you split the charger?did you use a file follower by paper to polish the intake?

Used a fine file mate, fitted to a rechargeable drill, took the intake snout off and smoothed it off, was quite lumpy in there and i was bored more than anything, so thought i'd tidy it up? :laugh::laugh: then just used a fine wet and dry to clean it up? :biggrin:

Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!
Bandit
12-07-2018, 08:42 PM #33

ormi so did you split the charger?did you use a file follower by paper to polish the intake?

Used a fine file mate, fitted to a rechargeable drill, took the intake snout off and smoothed it off, was quite lumpy in there and i was bored more than anything, so thought i'd tidy it up? :laugh::laugh: then just used a fine wet and dry to clean it up? :biggrin:


Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!

ormi
Posting Freak
3,006
12-07-2018, 10:01 PM
#34
Do you use sealer to put it back on?

[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
ormi
12-07-2018, 10:01 PM #34

Do you use sealer to put it back on?


[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more

Stoney
Posting Freak
2,117
12-07-2018, 11:04 PM
#35
ormi Do you use sealer to put it back on?

When I took mine apart, there was certainly some form of sealant used before.

Sent from my GT-I9100 using Tapatalk

[Image: tempsig2.jpg]
Confusedad: It was a tough call to make, but the Supercharged IS200 is being retired. Confusedad:
Stoney
12-07-2018, 11:04 PM #35

ormi Do you use sealer to put it back on?

When I took mine apart, there was certainly some form of sealant used before.

Sent from my GT-I9100 using Tapatalk


[Image: tempsig2.jpg]
Confusedad: It was a tough call to make, but the Supercharged IS200 is being retired. Confusedad:

Talisker
Member
118
17-07-2018, 02:47 AM
#36
So Ormi,

How are you going to block the silencer holes? Are you going to weld plates over them or use some other method?

Strange how everyone is reconditioning their chargers, I did mine about a month ago. I ported the intake and outlet snouts and cleaned all the gunk out of the inside.

I may well have a go at porting the triangular outlet if i can get hold of second supercharger to play with.

I've gone over the the Greddy Boost Cut Controller instead of the HKS FCD it works in a better way to the FCD. If you can get hold of one I recommend it to any supercharger owner.
Talisker
17-07-2018, 02:47 AM #36

So Ormi,

How are you going to block the silencer holes? Are you going to weld plates over them or use some other method?

Strange how everyone is reconditioning their chargers, I did mine about a month ago. I ported the intake and outlet snouts and cleaned all the gunk out of the inside.

I may well have a go at porting the triangular outlet if i can get hold of second supercharger to play with.

I've gone over the the Greddy Boost Cut Controller instead of the HKS FCD it works in a better way to the FCD. If you can get hold of one I recommend it to any supercharger owner.

Sparkystav
Administrator
14,683
17-07-2018, 06:46 AM
#37
Talisker I've gone over the the Greddy Boost Cut Controller instead of the HKS FCD it works in a better way to the FCD. If you can get hold of one I recommend it to any supercharger owner.

What I've been telling people for years mate.

OutlawJapClub Admin Team
Sparkystav
17-07-2018, 06:46 AM #37

Talisker I've gone over the the Greddy Boost Cut Controller instead of the HKS FCD it works in a better way to the FCD. If you can get hold of one I recommend it to any supercharger owner.

What I've been telling people for years mate.


OutlawJapClub Admin Team

ormi
Posting Freak
3,006
17-07-2018, 07:25 AM
#38
im just going to leave the silencer holes mate and just open the v up...
the only reason i done mine was i didnt know when the oil was changed and i wanted to check the rotors..
what diff will running the greddy do over running the hks

[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
ormi
17-07-2018, 07:25 AM #38

im just going to leave the silencer holes mate and just open the v up...
the only reason i done mine was i didnt know when the oil was changed and i wanted to check the rotors..
what diff will running the greddy do over running the hks


[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more

Sparkystav
Administrator
14,683
17-07-2018, 07:39 AM
#39
The BCC is almost exactly like the orignal black box that clamps the voltage once it goes over a set figure, rather than the FCD that "lies" to the ecu right through the range when its not needed, only once the MAP pressure gets towards the boost cut.

OutlawJapClub Admin Team
Sparkystav
17-07-2018, 07:39 AM #39

The BCC is almost exactly like the orignal black box that clamps the voltage once it goes over a set figure, rather than the FCD that "lies" to the ecu right through the range when its not needed, only once the MAP pressure gets towards the boost cut.


OutlawJapClub Admin Team

ormi
Posting Freak
3,006
17-07-2018, 07:47 AM
#40
aaaaa i might look in to that then

[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
ormi
17-07-2018, 07:47 AM #40

aaaaa i might look in to that then


[Image: ormiedit1-2.jpg]
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more

Pages (6): Previous 1 2 3 4 5 6 Next
Recently Browsing
 5 Guest(s)
Recently Browsing
 5 Guest(s)
Related Threads…
Replies 4
Views 341
13-12-2023, 02:06 PM
Last Post by Moley
Replies 3
Views 478
09-11-2023, 03:46 AM
Last Post by Dinho
Replies 17
Views 725
06-11-2022, 01:49 AM
Last Post by Rabster
Replies 4
Views 1,380
02-11-2022, 10:55 AM
Last Post by Sparkystav
Replies 2
Views 314
06-08-2022, 11:58 AM
Last Post by Brad92
Replies 38
Views 1,213
23-02-2022, 01:20 PM
Last Post by beamstezza
Replies 2
Views 359
18-10-2021, 02:04 AM
Last Post by Rabster
Replies 7
Views 477
03-09-2021, 11:04 AM
Last Post by FOSSIL FUELS
Replies 1
Views 494
29-08-2021, 09:59 AM
Last Post by Sparkystav
Replies 35
Views 7,777
04-08-2021, 04:34 AM
Last Post by cjoseph