JapCarForum Car Manufacturers Lexus/Toyota IS200 / IS300 / SPORTCROSS / Altezza my HIDs aint working

my HIDs aint working

my HIDs aint working

Pages (4): Previous 1 2 3 4
steviewevie
Posting Freak
7,993
04-01-2017, 11:43 AM
#31
Mine is on the low horizontal flat bit, to the bottom left of Dean's pic.

[Image: Sig-enginebay.jpg]
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
04-01-2017, 11:43 AM #31

Mine is on the low horizontal flat bit, to the bottom left of Dean's pic.


[Image: Sig-enginebay.jpg]
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !

Bandit
Posting Freak
6,464
04-01-2017, 09:51 PM
#32
I put mine here matey, nice flat surface and used VHB Tape to stick it on with? looked quite tidy too as the wiring follows the body :thumbup1:

[Image: DSCF1492_edited-1.jpg]
Edited 16-02-2010, 09:05 AM by Bandit.

Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!
Bandit
04-01-2017, 09:51 PM #32

I put mine here matey, nice flat surface and used VHB Tape to stick it on with? looked quite tidy too as the wiring follows the body :thumbup1:

[Image: DSCF1492_edited-1.jpg]


Lexus IS200 Sport Navigator (Now being stripped again) :blink:


Now Don't Forget The REP!!!

Sparkystav
Administrator
14,683
04-01-2017, 10:54 PM
#33
Take your headlight out mate and mount them below the headlight so you cant see them,

or take the bumper off put it in the massive gap between the wheel and the bumper

OutlawJapClub Admin Team
Sparkystav
04-01-2017, 10:54 PM #33

Take your headlight out mate and mount them below the headlight so you cant see them,

or take the bumper off put it in the massive gap between the wheel and the bumper


OutlawJapClub Admin Team

kam05
Senior Member
387
05-01-2017, 12:30 AM
#34
I've stuck my ballasts to the bodywork using velcro pads- you can also use sticky pads (the same stuff you use to stick number plates to bumpers?)

[SIGPIC][/SIGPIC]

Mods:...WIM geometry setup & fine tune, K&N Air filter, Stainless steel A/C rings, Brodit phone kit, Stainless steel clock surround, B&M Shortshifter & LED Domelight, Maplight & Sun Visors, OEM Chrome exhaust tip, OEM rubber bootliner, Fan type windscreen washer jets, LS430 Side repeaters, OEM LE grille, OEM cargo net, Front OEM armrest
kam05
05-01-2017, 12:30 AM #34

I've stuck my ballasts to the bodywork using velcro pads- you can also use sticky pads (the same stuff you use to stick number plates to bumpers?)


[SIGPIC][/SIGPIC]

Mods:...WIM geometry setup & fine tune, K&N Air filter, Stainless steel A/C rings, Brodit phone kit, Stainless steel clock surround, B&M Shortshifter & LED Domelight, Maplight & Sun Visors, OEM Chrome exhaust tip, OEM rubber bootliner, Fan type windscreen washer jets, LS430 Side repeaters, OEM LE grille, OEM cargo net, Front OEM armrest

Pages (4): Previous 1 2 3 4
Recently Browsing
 5 Guest(s)
Recently Browsing
 5 Guest(s)
Related Threads…
Replies 6
Views 347
28-06-2019, 10:43 AM
Last Post by purplewitch
Replies 11
Views 664
28-09-2018, 11:44 AM
Last Post by rob
Replies 9
Views 497
18-03-2018, 07:56 AM
Last Post by danielson
Replies 8
Views 375
06-05-2017, 01:04 PM
Last Post by parthiban
Replies 17
Views 1,007
18-01-2017, 10:52 AM
Last Post by Sparkystav
Replies 41
Views 1,262
03-09-2016, 09:08 AM
Last Post by parthiban
Replies 11
Views 530
04-06-2016, 11:22 AM
Last Post by Andy-R.