My Toyota MR2 build thread - 1994 GT-S
My Toyota MR2 build thread - 1994 GT-S
Went to Toyota today, another £130 dropped on gaskets and studs and bolts and nuts... replacing every gasket in the exhaust tract - while I've had the inlet manifold off I've replaced that gasket with the phenolic one a few pages earlier so I don't need to buy that one from Toyota. All new studs and nuts (most of the nuts are single-use locking ones anyway) should make sure there's no more exhaust blowing!!
![[Image: IMG00012-20100809-2031.jpg]](http://img.photobucket.com/albums/v189/jerem_rsv_uk24/IMG00012-20100809-2031.jpg)
Rear spoiler should look like this once fitted. Obviously this guy has fitted a lot more parts (lexus style rear lights, black trim strips, carbon vents, black wheels, window tints) that I don't have but you get the idea. I'm not going to paint the panels on the end caps black though.
Are you not going for the lexus lights then? :laugh:
Steve
Steve@EdgeAutomotive
26-08-2017, 09:39 AM #463i do like the Rev 5 spoiler, Always fancied on myself, but i think i might stick with the Rev 3.
Are you not going for the lexus lights then? :laugh:
Steve
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
26-08-2017, 09:57 AM #464The only place for "Lexus" lights is on a Lexus.:Shooting: even then its debatable......
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
I'm not sure on the rev5 spoiler yet but it was cheap. If I decide I don't like it I'll shift it on and put the rev3 back on!
I have done a few more things now:
Bought all new gaskets, studs and nuts for head -> manifold, manifold -> turbo and turbo -> downpipe. 3 gaskets, 19 studs and 19 nuts! NOT CHEAP. Got the gaskets for the rev5 spoiler -> bootlid as well, they were quite cheap.
Ordered a nice shiny stainless 3.75" v-band clamp to hold the turbo together.
Ordered a new speedo 'clamping' converter & delimiter. The existing one messes with the power steering.
Posted all the cast exhaust parts (manifold, turbo exhaust housing, downpipe & Blitz decat) off to Zircotec for ceramic coating. 22.5KG!!
Posted the injectors off to get cleaned, balanced and new o-rings/seats.
They aren't my injectors as we decided leaving the fuel system open for potentially quite a long time was a bad idea. Rather than taping up all the injector holes and the fuel rail etc I've sent off a spare set of injectors then they can just be swapped out.
lol, no... I'm not a fan of Lexus lights on Lexuses, let alone anything else! :lol:
I'm not sure on the rev5 spoiler yet but it was cheap. If I decide I don't like it I'll shift it on and put the rev3 back on!
I have done a few more things now:
Bought all new gaskets, studs and nuts for head -> manifold, manifold -> turbo and turbo -> downpipe. 3 gaskets, 19 studs and 19 nuts! NOT CHEAP. Got the gaskets for the rev5 spoiler -> bootlid as well, they were quite cheap.
Ordered a nice shiny stainless 3.75" v-band clamp to hold the turbo together.
Ordered a new speedo 'clamping' converter & delimiter. The existing one messes with the power steering.
Posted all the cast exhaust parts (manifold, turbo exhaust housing, downpipe & Blitz decat) off to Zircotec for ceramic coating. 22.5KG!!
Posted the injectors off to get cleaned, balanced and new o-rings/seats.
They aren't my injectors as we decided leaving the fuel system open for potentially quite a long time was a bad idea. Rather than taping up all the injector holes and the fuel rail etc I've sent off a spare set of injectors then they can just be swapped out.
What rear bumper do you have? Have you got the Tom's with Tom's skirts with border front?
i was going to go down this route, but i think i want a different front end, Perhaps mod the original one with a lip.
Steve
Steve@EdgeAutomotive
26-08-2017, 10:35 AM #466Sounds good!
What rear bumper do you have? Have you got the Tom's with Tom's skirts with border front?
i was going to go down this route, but i think i want a different front end, Perhaps mod the original one with a lip.
Steve
Steve
Steve@EdgeAutomotive
26-08-2017, 10:40 AM #468It does look nice from the little picture i can see lol I might have to look into that. I'm going down the smoothed bump strips route, but so i'm still able to take off the bumpers and skirts.
Steve
![[Image: Smoothed2.jpg]](http://www.edgeautomotive.co.uk/Smoothed2.jpg)
![[Image: Smoothed2-2.jpg]](http://www.edgeautomotive.co.uk/Smoothed2-2.jpg)
Oh er, I didn't spot the link!
Steve
Steve@EdgeAutomotive
26-08-2017, 10:52 AM #470I'm not fully smoothing it in, There will still be a 'Join' line. It'll look like this one..
Oh er, I didn't spot the link!
Steve
7 Guest(s)
7 Guest(s)
Views 873
Last Post by
Views 1,458
Last Post by
Views 5,926
Last Post by
Views 3,085
Last Post by
Views 1,921
Last Post by
Views 6,360
Last Post by
Views 689
Last Post by
Views 856
Last Post by