My Toyota MR2 build thread - 1994 GT-S
My Toyota MR2 build thread - 1994 GT-S
It's a Falcon VIFWIN12 which cost £15 from eBay. It's quite flexible, in that it will work with alarms that do either -ve or +ve triggers, even if they don't support total closure. You can even add it into any old remote central locking system, in fact. All it needs is either a +ve or -ve trigger to act. It has an override so that if you tell your alarm to lock and then realise that closing the window will cut some child/cat/significant other/baguette in half, you can press unlock again and the windows will cease. It monitors resistance in the electric window motor to determine when the window is completely closed, and as a result will also cut off if there is an obstruction blocking the window.
The unit has 2 looms, one for power and one for triggers. I'll refer to the loom with the fuse on as loom A, and the loom with no fuse on as loom B.
This is how the wiring will tie up:
Loom Colour | Function | MR2 Wire
Loom A:
Red | Batt +ve | Off pin something on steering column
Black | Ground | Ground point behind driver's side kick panel
Blue/White | Window 1 up, switch side | green wire, pin 3 of electric window control in driver door
Green/White | Window 1 up, motor side | as above, but motor-side
Blue | Window 2 up, switch side | red/blue wire, pin 10 of electric window control in driver door
Green | Window 2 up, motor side | as above, but motor-side
Loom B:
Green / Black | Acc +ve | Again, in steering column
White / Green | + unlock | Not used with Toad Ai606
White / Red | - unlock | *probably* blue/red on Toad loom, need to check
White / Black | + trigger | Not used with Toad Ai606
Red / White | - trigger | brown/white wire on Toad loom (this keeps the programmable output free for something else)
Orange | Ground output | Not used
I find it easier to write this stuff down before I do it so there it is. Time to get busy!
Total closure module turned up today. Not being one to hang around, I've got it to bits all over my desk at work
It's a Falcon VIFWIN12 which cost £15 from eBay. It's quite flexible, in that it will work with alarms that do either -ve or +ve triggers, even if they don't support total closure. You can even add it into any old remote central locking system, in fact. All it needs is either a +ve or -ve trigger to act. It has an override so that if you tell your alarm to lock and then realise that closing the window will cut some child/cat/significant other/baguette in half, you can press unlock again and the windows will cease. It monitors resistance in the electric window motor to determine when the window is completely closed, and as a result will also cut off if there is an obstruction blocking the window.
The unit has 2 looms, one for power and one for triggers. I'll refer to the loom with the fuse on as loom A, and the loom with no fuse on as loom B.
This is how the wiring will tie up:
Loom Colour | Function | MR2 Wire
Loom A:
Red | Batt +ve | Off pin something on steering column
Black | Ground | Ground point behind driver's side kick panel
Blue/White | Window 1 up, switch side | green wire, pin 3 of electric window control in driver door
Green/White | Window 1 up, motor side | as above, but motor-side
Blue | Window 2 up, switch side | red/blue wire, pin 10 of electric window control in driver door
Green | Window 2 up, motor side | as above, but motor-side
Loom B:
Green / Black | Acc +ve | Again, in steering column
White / Green | + unlock | Not used with Toad Ai606
White / Red | - unlock | *probably* blue/red on Toad loom, need to check
White / Black | + trigger | Not used with Toad Ai606
Red / White | - trigger | brown/white wire on Toad loom (this keeps the programmable output free for something else)
Orange | Ground output | Not used
I find it easier to write this stuff down before I do it so there it is. Time to get busy!
Bizarrely the TC module seems to close one window first then the other. The set on the wires with solid colours go first, then once that's finished the other winds up, so I'd recommend connecting the windows the other way around to the way I have (as you would mostly have the driver's window open).
[PICS TO GO HERE]
- Amp board & subs reinstalled DONE
- Speaker wire repeair for driver's door components DONE
- Electric mirror control repair Investigated, spare control I've got is wrong one
- Alarm siren & engine bay switch working DONE
- Alarm total closure DONE
- HKS CAMP installed DONE
- Accessory Fuse & Relay box installed
- Fan kit fitted
- Omori 45mm boost gauge fitted in-dash Gauge fitted, needs longer vac hose, ordered. WHERE THE **** IS MY VAC HOSE, DEMON TWEEKS?!
- Side strip mounts repaired
- Foglights reinstalled
- Front bumper repair (fibreglass)
- Reversing camera reinstalled
- Exhaust flexi repair
Total closure fitted today while I was hanging around at the rolling road day :thumbup: Wasn't quite as detailed above as I took the +ve's from the fusebox in the driver footwell and the MR2 is +ve locking so the white/green on loom 2 had to be used. Also the white wire had to be used from the Toad alarm, not the brown one which pulses every 2 seconds for a flashing LED etc.
Bizarrely the TC module seems to close one window first then the other. The set on the wires with solid colours go first, then once that's finished the other winds up, so I'd recommend connecting the windows the other way around to the way I have (as you would mostly have the driver's window open).
[PICS TO GO HERE]
- Amp board & subs reinstalled DONE
- Speaker wire repeair for driver's door components DONE
- Electric mirror control repair Investigated, spare control I've got is wrong one
- Alarm siren & engine bay switch working DONE
- Alarm total closure DONE
- HKS CAMP installed DONE
- Accessory Fuse & Relay box installed
- Fan kit fitted
- Omori 45mm boost gauge fitted in-dash Gauge fitted, needs longer vac hose, ordered. WHERE THE **** IS MY VAC HOSE, DEMON TWEEKS?!
- Side strip mounts repaired
- Foglights reinstalled
- Front bumper repair (fibreglass)
- Reversing camera reinstalled
- Exhaust flexi repair
A load of silicon hose so that I can do a bit of engine dress and finally plumb in my omori gauge
Falcon boot popper to sort out a remote boot release off the alarm
ARP flywheel bolts to go with the Fidanza flywheel I have lying around
Walbro 225lph fuel pump for when the new turbo goes on
Got a full set of goodridge braided brake hoses and braided clutch hose too!! And I collect the ATS Racing TD06 kit + SSQV on Saturday...
Man have I had a load of goodies turn up today!!
A load of silicon hose so that I can do a bit of engine dress and finally plumb in my omori gauge
Falcon boot popper to sort out a remote boot release off the alarm
ARP flywheel bolts to go with the Fidanza flywheel I have lying around
Walbro 225lph fuel pump for when the new turbo goes on
Got a full set of goodridge braided brake hoses and braided clutch hose too!! And I collect the ATS Racing TD06 kit + SSQV on Saturday...
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-06-2016, 10:32 PM #24Sounds great, we want pics ! :biggrin:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie Sounds great, we want pics ! :biggrin:
As requested...
Boot popper, ARP flywheel bolts & Walbro fuel pump:
![[Image: goodies.jpg]](http://theshado.ws/images/imoc/goodies.jpg)
New turbo
![[Image: td06.jpg]](http://theshado.ws/images/imoc/td06.jpg)
Braided brake hoses & Clutch hose:
![[Image: goodridge.jpg]](http://theshado.ws/images/imoc/goodridge.jpg)
Fidanza Lightweight Flywheel:
![[Image: fidanza.jpg]](http://theshado.ws/images/imoc/fidanza.jpg)
The manifold the turbo is attached to won't fit my car as it's from a Rev2 so I will need to have the wastegate ****** mounted onto my manifold in such a way that the screamer pipe still fits around the turbo. A job for Hayward & Scott I think (who will also be repairing my exhaust).
Along with the stuff pictured I also picked up some tidier dash plastics, carpet etc to clean up my ageing interior, and an HKS SSQV which I have fitted. I'll take an engine bay shot later so I've got a reference for fitting the turbo. I need to get oil and water lines for the turbo as it didn't come with any, so my contact at Goodridge will almost certainly be getting that job! My list is getting longer...
- Amp board & subs reinstalled DONE
- Speaker wire repair for driver's door components DONE
- Alarm siren & engine bay switch working DONE
- Alarm total closure DONE
- HKS CAMP installed DONE
- Omori 45mm boost gauge fitted in-dash DONE
- HKS SSQV fitted DONE
- Electric mirror control repair Investigated, spare control I've got is wrong one
- Fit Walbro fuel pump
- Alarm boot release
- Accessory Fuse & Relay box installed
- Fan kit fitted
- Side strip mounts repaired
- Foglights reinstalled
- Front bumper repair (fibreglass)
- Reversing camera reinstalled
- Exhaust flexi repair
- New heater controls, boot & fuel flap release & driver's carpet
- TD06 oil & water lines
- Wastegate ****** welded onto rev3 manifold
- TD06 fitted
- Gearbox bellhousing repair
- TRD Engine mounts
- Fidanza flywheel fitted
- Engine bay cleanup (powder coated rocker cover + inlet manifold + chargecooler, hoses colour coordinated, some new gaskets & clean up oil leak)
steviewevie Sounds great, we want pics ! :biggrin:
As requested...
Boot popper, ARP flywheel bolts & Walbro fuel pump:
New turbo
Braided brake hoses & Clutch hose:
Fidanza Lightweight Flywheel:
The manifold the turbo is attached to won't fit my car as it's from a Rev2 so I will need to have the wastegate ****** mounted onto my manifold in such a way that the screamer pipe still fits around the turbo. A job for Hayward & Scott I think (who will also be repairing my exhaust).
Along with the stuff pictured I also picked up some tidier dash plastics, carpet etc to clean up my ageing interior, and an HKS SSQV which I have fitted. I'll take an engine bay shot later so I've got a reference for fitting the turbo. I need to get oil and water lines for the turbo as it didn't come with any, so my contact at Goodridge will almost certainly be getting that job! My list is getting longer...
- Amp board & subs reinstalled DONE
- Speaker wire repair for driver's door components DONE
- Alarm siren & engine bay switch working DONE
- Alarm total closure DONE
- HKS CAMP installed DONE
- Omori 45mm boost gauge fitted in-dash DONE
- HKS SSQV fitted DONE
- Electric mirror control repair Investigated, spare control I've got is wrong one
- Fit Walbro fuel pump
- Alarm boot release
- Accessory Fuse & Relay box installed
- Fan kit fitted
- Side strip mounts repaired
- Foglights reinstalled
- Front bumper repair (fibreglass)
- Reversing camera reinstalled
- Exhaust flexi repair
- New heater controls, boot & fuel flap release & driver's carpet
- TD06 oil & water lines
- Wastegate ****** welded onto rev3 manifold
- TD06 fitted
- Gearbox bellhousing repair
- TRD Engine mounts
- Fidanza flywheel fitted
- Engine bay cleanup (powder coated rocker cover + inlet manifold + chargecooler, hoses colour coordinated, some new gaskets & clean up oil leak)
toxo lol brilliant, the forum censors the word fl@nge!
:lol:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
23-06-2016, 04:33 AM #28toxo lol brilliant, the forum censors the word fl@nge!
:lol:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
24-06-2016, 04:42 AM #30Yay for the pics ! :thumbup:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
1 Guest(s)
1 Guest(s)
Views 982
Last Post by
Views 1,530
Last Post by
Views 6,161
Last Post by
Views 3,222
Last Post by
Views 2,023
Last Post by
Views 6,554
Last Post by
Views 717
Last Post by
Views 885
Last Post by