Fitting IS300 exhaust on an IS200
Fitting IS300 exhaust on an IS200
im not saying im always correct i could still be wrong in what i have found but i do hope not Ormi can you confirm the location of the sensors so we can get this back on track
to put this topic back on track
from what i understand i would need to use an O2 Simulator in order to save drilling holes in the exhaust...
Stav can you confirm then we can edit this thread and stick it with the relevant details
internet can be a dangerous place if you dont do research properly always check, check again, double check then post save appearing foolish with responses.
im not saying im always correct i could still be wrong in what i have found but i do hope not Ormi can you confirm the location of the sensors so we can get this back on track
to put this topic back on track
from what i understand i would need to use an O2 Simulator in order to save drilling holes in the exhaust...
Stav can you confirm then we can edit this thread and stick it with the relevant details
dont forget you would need to use another cap type bung in the floor where the cabling would go or you could end up with a wet carpet
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
is300_dino
09-12-2017, 04:28 AM #13An O2 sim would/should do the trick andy, then just use a bung in the hole where the original sensor would go, and should work a treat dont forget you would need to use another cap type bung in the floor where the cabling would go or you could end up with a wet carpet
jae 2010 best lexus category show and shine winner
jae 2010 ice outlaw award 2nd place
jae 2011 ice outlaw award 1st place
Clearly depends on which 'zorst you have Rabster???????
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
09-12-2017, 05:04 AM #14Hmmmm, would it not be far easier to do a swap (£'s either way) with Phil01 and yourself Rabster, he is buying an IS200 'zorst that won't work without modding - from Demon, and you have an IS300 'zorst that also won't fit without modding.....................
Clearly depends on which 'zorst you have Rabster???????
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
All I need is a simulator then and no holes to block up as there are no holes as the Is300 it's located pre cat so mine is all good
Sounds like Oli and phil will have fun though lol
Rabster That sounds sensible mate but Oli clearly wants extra hastle lol.
All I need is a simulator then and no holes to block up as there are no holes as the Is300 it's located pre cat so mine is all good
Sounds like Oli and phil will have fun though lol
I think so.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
09-12-2017, 06:00 AM #17Rabster That sounds sensible mate but Oli clearly wants extra hastle lol.
All I need is a simulator then and no holes to block up as there are no holes as the Is300 it's located pre cat so mine is all good
Sounds like Oli and phil will have fun though lol
I think so.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
9 Guest(s)
9 Guest(s)
Views 464
Last Post by
Views 678
Last Post by
Views 1,100
Last Post by
Views 301
Last Post by
Views 1,108
Last Post by
Views 345
Last Post by
Views 447
Last Post by
Views 482
Last Post by
Views 7,689
Last Post by