reset Throttle Positioning Sensor
reset Throttle Positioning Sensor
any idea's on how to reset it
jay_russell
09-10-2017, 08:50 AM #1ok well this might be what is giving me all the grief after the small problems i had.
any idea's on how to reset it
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
09-10-2017, 09:05 AM #2It might seem simple, but have you tried an ECU reset?
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
jay_russell
09-10-2017, 09:08 AM #3yes mate. had the battery out for an hour while fixing the short. think this might have messed up the throttle sensor. going to put it on the tester tomorrow
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
10-10-2017, 06:20 AM #4Try this - http://bahamutcars.free.fr/workshop/IS_9...i_0037.pdf
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
jay_russell
10-10-2017, 06:39 AM #5well found the problem. was a fuse missing. not sure how that happened but all done. fixed the o2 sensor fault and fitted the afr gauge plus fitted new break disks all round. cleared all fault codes and did the needles on my gauge. looks ok but will sand them down and paint them with some glass paint
jay_russell well found the problem. was a fuse missing. not sure how that happened but all done. fixed the o2 sensor fault and fitted the afr gauge plus fitted new break disks all round. cleared all fault codes and did the needles on my gauge. looks ok but will sand them down and paint them with some glass paint
Which fuse was missing ?
Great news that you got it sorted :biggrin:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
10-10-2017, 08:42 AM #6jay_russell well found the problem. was a fuse missing. not sure how that happened but all done. fixed the o2 sensor fault and fitted the afr gauge plus fitted new break disks all round. cleared all fault codes and did the needles on my gauge. looks ok but will sand them down and paint them with some glass paint
Which fuse was missing ?
Great news that you got it sorted :biggrin:
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
jay_russell
10-10-2017, 08:51 AM #7it was one in the engine bay fuse box. not sure if i took it out to check it and put it back in the wrong place but thats what was causing all the problems. aswell as a o2 sensor i shopped of ebay that turnerd out to be a fuel air sensor. hence the engine light on. but picked up a old one from work that was working so just changed the plugs over.
jay_russell
10-10-2017, 08:57 AM #8i have contacted the ebay seller to confirm it's not a o2 sensor and will wait to see what he says
1 Guest(s)
1 Guest(s)
Views 1,095
Last Post by
Views 276
Last Post by
Views 450
Last Post by
Views 636
Last Post by
Views 282
Last Post by
Views 927
Last Post by