My little project - IS200 Turbo
My little project - IS200 Turbo
17-01-2019, 03:00 AM
![[Image: IMG_1035.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/IMG_1035.jpg)
![[Image: IMG_1034.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/IMG_1034.jpg)
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-01-2019, 03:00 AM #1,281And here's the cal switch (now you see it, now you don't) :
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
17-01-2019, 03:24 AM
17-01-2019, 03:27 AM
Rabster steve why not replace the factory led on the cluster with the toad LED that keeps it with the OEM look of the dashboard......
Yeah, that is something I'd considered (and forgotten). Thanks for the reminder !
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-01-2019, 03:27 AM #1,283Rabster steve why not replace the factory led on the cluster with the toad LED that keeps it with the OEM look of the dashboard......
Yeah, that is something I'd considered (and forgotten). Thanks for the reminder !
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
17-01-2019, 03:37 AM
Rabster thats ok here to help :p
the updates are looking good so far too
Thanks
Do you think it would be easy enough to install the LED into the dash ? Would it just need an appropriate bezel ?
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-01-2019, 03:37 AM #1,285Rabster thats ok here to help :p
the updates are looking good so far too
Thanks
Do you think it would be easy enough to install the LED into the dash ? Would it just need an appropriate bezel ?
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
17-01-2019, 03:40 AM
If you do go down that route, remember the TOAD LED is dual colour, which the stock one probably isn't, and it's the wrong way round for most multi-colour LEDs. Usually you'd have multiple positives with a shared negative but the TOAD one is shared positive and multiple negatives. Also it needs to be a smoked style LED rather than one with a totally clear housing.
17-01-2019, 03:45 AM
toxo If you do go down that route, remember the TOAD LED is dual colour, which the stock one probably isn't, and it's the wrong way round for most multi-colour LEDs. Usually you'd have multiple positives with a shared negative but the TOAD one is shared positive and multiple negatives. Also it needs to be a smoked style LED rather than one with a totally clear housing.
Thanks, but are you saying it's going to need to be soldered onto the board behind the panel ? I was hoping for a "poke it through the hole" type of solution.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-01-2019, 03:45 AM #1,287toxo If you do go down that route, remember the TOAD LED is dual colour, which the stock one probably isn't, and it's the wrong way round for most multi-colour LEDs. Usually you'd have multiple positives with a shared negative but the TOAD one is shared positive and multiple negatives. Also it needs to be a smoked style LED rather than one with a totally clear housing.
Thanks, but are you saying it's going to need to be soldered onto the board behind the panel ? I was hoping for a "poke it through the hole" type of solution.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
17-01-2019, 03:47 AM
I imagine that's probably how the stock one is done - it won't be held in with an LED clip because it will be relatively flush mounted, so it'll be held in place by its legs.You could always attach 1 leg to the PCB for a +ve feed and then run the -ve legs to the TOAD alarm via wires.
Do you remember when I did mine? It's in the MR2's build thread somewhere.
Edited 28-02-2012, 01:22 PM by toxo.
Couldn't say without seeing the board I imagine that's probably how the stock one is done - it won't be held in with an LED clip because it will be relatively flush mounted, so it'll be held in place by its legs.
You could always attach 1 leg to the PCB for a +ve feed and then run the -ve legs to the TOAD alarm via wires.
Do you remember when I did mine? It's in the MR2's build thread somewhere.
17-01-2019, 03:51 AM
toxo Couldn't say without seeing the board
You could always attach 1 leg to the PCB for a +ve feed and then run the -ve legs to the TOAD alarm via wires.
Do you remember when I did mine? It's in the MR2's build thread somewhere.
I don't remember, no :o , but I will dig it out ! Thanks for the suggestions.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
17-01-2019, 03:51 AM #1,289toxo Couldn't say without seeing the board
You could always attach 1 leg to the PCB for a +ve feed and then run the -ve legs to the TOAD alarm via wires.
Do you remember when I did mine? It's in the MR2's build thread somewhere.
I don't remember, no :o , but I will dig it out ! Thanks for the suggestions.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
Recently Browsing
4 Guest(s)
4 Guest(s)
Recently Browsing
4 Guest(s)
4 Guest(s)
Related Threads…
Replies 1,312
Views 102,750
Views 102,750
25-03-2024, 02:10 AM
Last Post byZAIS200
Last Post by
Replies 1,341
Views 67,675
Views 67,675
08-02-2024, 01:53 AM
Last Post byWayne
Last Post by
Replies 4
Views 404
Views 404
18-12-2023, 02:55 AM
Last Post byRabster
Last Post by
Replies 20
Views 1,483
Views 1,483
08-10-2023, 03:59 AM
Last Post byWayne
Last Post by
Replies 42
Views 3,127
Views 3,127
04-10-2023, 03:52 PM
Last Post byWayne
Last Post by