Jimbobs Lexus IS200 Turbo!

john wan
Posting Freak

890

10-02-2020, 05:50 AM

#561

Know what you mean about the weather top half of me is alright just me ****** legs an feet get wet an cold ha ha ha

Jimbob-T-Lex
Moderator

1,674

11-02-2020, 08:07 AM

#562

Well got a lil bit done this weekend but freezing out there
Well the manifold and wastegate are now all fitted so the turbo could go on and i could start the plumbing of intercooler

[Image: 56AB42F5-921B-435D-8A12-CA56E86E4B4A-876...cfeec9.jpg]

[Image: 56AB42F5-921B-435D-8A12-CA56E86E4B4A-876...cfeec9.jpg]

[Image: 45AF95D7-1A2E-4032-BAFA-4C0CA6F9FCEF-876...e681e3.jpg]

Still got to do the turbo side of the intercooler and remount the left and right impact sensors

Got the 3 lambda sensor bosses welded on the down pipe so fitted them also today

[Image: 02381916-1906-4748-A5AE-35246EF5E629-876...6ba70b.jpg]

[Image: 02381916-1906-4748-A5AE-35246EF5E629-876...6ba70b.jpg]

Fitted the plugs onto the gearbox as forgot bout them oops lol

2 x questions what is this pipe for that runs underneath from the engine bay a vacuum for something i think and has what i think is a filter???

[Image: AADF520F-6467-4817-BC54-C4E63D5875E5-876...ca74ec.jpg]

[Image: AADF520F-6467-4817-BC54-C4E63D5875E5-876...ca74ec.jpg]

Also on the map sensor is there any need to keep the screw end on or can i just take off and plumb straight into vacuum manifold?? the screw end looks too big to be just a vacuum tap off??

[Image: 791D97C0-72E6-436B-BD4A-49F9E67D07A6-876...10358f.jpg]

[Image: 791D97C0-72E6-436B-BD4A-49F9E67D07A6-876...10358f.jpg]

Slowly getting there still few bits to do with wiring like the injectors, changing the drive by wire and few greddy wires left
plumb the turboside intercooler
fit oilcooler on the front
fit oil pressure switcg relocator
greddy 3 bar map sensor
fit and plumb vacuum manifold
wire in FCD
fit micro switch to pedal for idle signal

As you can see still a fair bit but got week after next off so ill get alot done then but starting to look the part just need to get is sounding the part pmsl

mattlaw
Senior Member

572

11-02-2020, 08:14 AM

#563

Maybe a daft question but why3 lambda sensors? Wouldn't it have been easier to splice the front 2 together and then use a sim for the rear?

Jimbob-T-Lex
Moderator

1,674

11-02-2020, 08:18 AM

#564

No particular reason mate there was enough room so went with three 2 are from the normal manifold and 1 is for my air/fuel gauge and then still got my one at the rear

toxo
Posting Freak

4,843

11-02-2020, 08:18 AM

#565

The 'screw-on' bit on the MAP sensor is a filter. You should keep it.

Edited 24-03-2013, 05:54 PM by toxo.

Jimbob-T-Lex
Moderator

1,674

11-02-2020, 08:20 AM

#566

Sweet cheers toxo appreciated one question down Smile

Jimbob-T-Lex
Moderator

1,674

11-02-2020, 10:37 AM

#567

Oh forgot to ask anyone got a bottom rubber mount for the radiator mine has been nicked by the fairys!! pmsl

Sparkystav
Administrator

14,683

11-02-2020, 01:48 PM

#568

jimbob150385 Oh forgot to ask anyone got a bottom rubber mount for the radiator mine has been nicked by the fairys!! pmsl

Ask the sxe boys. Should be one on the sick bucket.

Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.

OutlawJapClub Admin Team

Sparkystav
Administrator

14,683

11-02-2020, 01:49 PM

#569

And the pipe is for the carbon canister Eco thing. Unneeded but the ecu will have a fit so leave it for now.

Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.

OutlawJapClub Admin Team

Jimbob-T-Lex
Moderator

1,674

11-02-2020, 01:54 PM

#570

Oh right so just plumb this into my vacuum manifold aswell then cheers mate ur engine is looking good mate!!!! Just want to get mine started then do all the tidy up of bay and wiring after

Recently Browsing
9 Guest(s)