JapCarForum Cars, Cars, Cars! Project Cars Altezza Build!

Altezza Build!

Altezza Build!

Pages (18): Previous 114 15 16 17 18  
Sparkystav
Administrator
14,683
18-06-2022, 10:27 PM
Decent upgrade mate. Did you mention Ojc for a discount?

The fcon is a good bit of kit but don't you have to be a power writer to get into it?

OutlawJapClub Admin Team
Sparkystav
18-06-2022, 10:27 PM #171

Decent upgrade mate. Did you mention Ojc for a discount?

The fcon is a good bit of kit but don't you have to be a power writer to get into it?


OutlawJapClub Admin Team

Tosh21
Member
171
18-06-2022, 11:46 PM
Yea the main reason I went for meister was the discount. Everything else is the same ish price or not in stock. Very impressed with them so far.

Yea there only 3 or 4 people in the UK who can actually tune them but it was £400 with a denso map sensor and a plug and play harness for the tezza. I couldn't really argue the price and I've had 2 power fcs blow on me now. A new pfc is 425 quid and I don't wana risk getting caught with a massive £150 import tax bill again.

Trying to push to get it boosted by jae
Tosh21
18-06-2022, 11:46 PM #172

Yea the main reason I went for meister was the discount. Everything else is the same ish price or not in stock. Very impressed with them so far.

Yea there only 3 or 4 people in the UK who can actually tune them but it was £400 with a denso map sensor and a plug and play harness for the tezza. I couldn't really argue the price and I've had 2 power fcs blow on me now. A new pfc is 425 quid and I don't wana risk getting caught with a massive £150 import tax bill again.

Trying to push to get it boosted by jae

Tosh21
Member
171
18-07-2022, 12:00 AM
Think I need to roll my arches.. and paint them!!

[Image: IMAG0735_zpsibi5ucjz.jpg]

Exhaust was scrapping on leafs and I didn't want to raise the car any higher, it already looks too high Sad so took off the exhaust to remake it and sit it further up. Some nice colors from the heat

[Image: IMAG0761_zpsxpd3yalf.jpg]

The damage from trying to get over a speed bump before abandoning the car at the side of the road and walking home

[Image: IMAG0762_zpsh2bvqvii.jpg]

Raised her right up, sits above the chassis arms now so it shouldn't be getting snagged all the time. Fitted a flexi too, not really needed but it was more to save me time on trying to get the pipes to fit together again after raising the front half. The front and rear section wouldn't meet if it was solid.

[Image: IMAG0765_zps7wwumdup.jpg]

Made a ghetto looking PAS to AC adapter plate

[Image: IMAG0770_zpsuiiuvlku.jpg]

Fitted ghetto plate to where the AC was

[Image: IMAG0771_zpsoaa4wwsa.jpg]

Made some hoses for the reservoir and plumbed everything up. The reservoir comes off the old PAS bolt holes and sit in front of the engine away from all the hot bits so hopefully It will live a bit longer.

[Image: IMAG0773_zpsj39dsiir.jpg]

Struggling with a belt though, can't fit the tensioner in there so going to try a few different belts until I find one that isn't too tight when fitted and if not then will have to try make some sort of bracket for a tensioner.

Unfortunately, I don't think she will be boosted for JAE Sad Dam tax man has been taking too much off me for the last 3 months
Tosh21
18-07-2022, 12:00 AM #173

Think I need to roll my arches.. and paint them!!

[Image: IMAG0735_zpsibi5ucjz.jpg]

Exhaust was scrapping on leafs and I didn't want to raise the car any higher, it already looks too high Sad so took off the exhaust to remake it and sit it further up. Some nice colors from the heat

[Image: IMAG0761_zpsxpd3yalf.jpg]

The damage from trying to get over a speed bump before abandoning the car at the side of the road and walking home

[Image: IMAG0762_zpsh2bvqvii.jpg]

Raised her right up, sits above the chassis arms now so it shouldn't be getting snagged all the time. Fitted a flexi too, not really needed but it was more to save me time on trying to get the pipes to fit together again after raising the front half. The front and rear section wouldn't meet if it was solid.

[Image: IMAG0765_zps7wwumdup.jpg]

Made a ghetto looking PAS to AC adapter plate

[Image: IMAG0770_zpsuiiuvlku.jpg]

Fitted ghetto plate to where the AC was

[Image: IMAG0771_zpsoaa4wwsa.jpg]

Made some hoses for the reservoir and plumbed everything up. The reservoir comes off the old PAS bolt holes and sit in front of the engine away from all the hot bits so hopefully It will live a bit longer.

[Image: IMAG0773_zpsj39dsiir.jpg]

Struggling with a belt though, can't fit the tensioner in there so going to try a few different belts until I find one that isn't too tight when fitted and if not then will have to try make some sort of bracket for a tensioner.

Unfortunately, I don't think she will be boosted for JAE Sad Dam tax man has been taking too much off me for the last 3 months

Sparkystav
Administrator
14,683
18-07-2022, 03:21 AM
Is the tensioner not normally part of the bracket?

OutlawJapClub Admin Team
Sparkystav
18-07-2022, 03:21 AM #174

Is the tensioner not normally part of the bracket?


OutlawJapClub Admin Team

Tosh21
Member
171
18-07-2022, 04:34 AM
Nah not on the tezza annoyingly. It's a separate part which bolts to the ac but it's in the completely wrong place for this. I've got a few belts to try and if it doesn't work I'll get a stretch belt. Crazy how much more space there is now
Tosh21
18-07-2022, 04:34 AM #175

Nah not on the tezza annoyingly. It's a separate part which bolts to the ac but it's in the completely wrong place for this. I've got a few belts to try and if it doesn't work I'll get a stretch belt. Crazy how much more space there is now

Tosh21
Member
171
30-07-2022, 11:50 AM
Cleaned up the turbo housing so that bits of ali don't melt off and hit the turbine. Came up surprisingly nice!

[Image: IMAG0797_zps8xcecxfk.jpg]

Started doing some intercooler pipes, pretty easy really just had to move the ecu box a little to make space. Ran out of bends unfortunately so hopefully get a chance to do some more in a couple of weeks. Would have had it booked for a map on friday if I had had enough bends Sad

[Image: IMAG0799_zpsilvghmfa.jpg]

Not ready for JAE at all, not even time to wash the car, or plug up any holes! Should be a decent weekend anyway though
Tosh21
30-07-2022, 11:50 AM #176

Cleaned up the turbo housing so that bits of ali don't melt off and hit the turbine. Came up surprisingly nice!

[Image: IMAG0797_zps8xcecxfk.jpg]

Started doing some intercooler pipes, pretty easy really just had to move the ecu box a little to make space. Ran out of bends unfortunately so hopefully get a chance to do some more in a couple of weeks. Would have had it booked for a map on friday if I had had enough bends Sad

[Image: IMAG0799_zpsilvghmfa.jpg]

Not ready for JAE at all, not even time to wash the car, or plug up any holes! Should be a decent weekend anyway though

Sparkystav
Administrator
14,683
10-09-2023, 07:50 PM
what happened to this project mate?

OutlawJapClub Admin Team
Sparkystav
10-09-2023, 07:50 PM #177

what happened to this project mate?


OutlawJapClub Admin Team

Pages (18): Previous 114 15 16 17 18  
Recently Browsing
 2 Guest(s)
Recently Browsing
 2 Guest(s)
Related Threads…
Replies 19
Views 891
31-10-2023, 10:05 PM
Last Post by RCarter
Replies 20
Views 1,467
08-10-2023, 03:59 AM
Last Post by Wayne
Replies 95
Views 5,943
06-10-2023, 02:58 AM
Last Post by Wayne
Replies 42
Views 3,101
04-10-2023, 03:52 PM
Last Post by Wayne
Replies 28
Views 1,926
17-05-2023, 11:25 AM
Last Post by IS200_rider
Replies 54
Views 6,361
05-05-2023, 01:09 PM
Last Post by Sparkystav
Replies 10
Views 858
18-03-2023, 01:09 PM
Last Post by FOSSIL FUELS
Replies 10
Views 1,344
07-02-2023, 08:29 AM
Last Post by dimis
Replies 28
Views 3,369
30-07-2022, 06:45 PM
Last Post by Lexus RS200T