My little project - IS200 Turbo
My little project - IS200 Turbo
15-03-2017, 10:31 AM
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
15-03-2017, 10:31 AM #1,001The Subaru garage I went to when I had a Legacy had a wheel nut that wound on to the locking nut and cut into it, then turn the nut the way to undo the offending nut and it removed broken/stuck locking wheel nuts!!
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
15-03-2017, 10:32 AM
![[Image: Sig-enginebay.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/Sig-enginebay.jpg)
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
15-03-2017, 10:32 AM #1,002Yeah the trouble with that is because of the way it is split, there's a risk that doing that will end up tearing the rest of that bit off, leaving an almost-impossible-bit-to-remove-but-stuck-fast bit behind !
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
15-03-2017, 10:35 AM
Firstly, a bit I didn't know they even did - new section of the exhaust between the downpipe and the cat :
![[Image: IMG_0302.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/IMG_0302.jpg)
And here's the bit that I had known about but had completely forgotten ! Can you spot it ?
![[Image: IMG_0299.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/IMG_0299.jpg)
![[Image: IMG_0311.jpg]](http://i5.photobucket.com/albums/y179/SteveHammatt/IMG_0311.jpg)
No, not the rather obvious ARBs (which were on there already). But the stove-enamelled sump ! Complete with oil temp sensor going into the sump plug.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
steviewevie
15-03-2017, 10:35 AM #1,003Here are my "suprise" extra mods.
Firstly, a bit I didn't know they even did - new section of the exhaust between the downpipe and the cat :
And here's the bit that I had known about but had completely forgotten ! Can you spot it ?
No, not the rather obvious ARBs (which were on there already). But the stove-enamelled sump ! Complete with oil temp sensor going into the sump plug.
IS200 Turbo project now just about complete ! See my thread here and leave your comments.
Now running standalone Syvecs ECU and no stock ECU !
15-03-2017, 10:44 AM
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
Well if you are welding it up, you better make sure your wheel is protected before you start and it would also be a good idea to try and remove some of the paint / coating on the wheel nut.
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
15-03-2017, 11:13 AM
2tongues The Subaru garage I went to when I had a Legacy had a wheel nut that wound on to the locking nut and cut into it, then turn the nut the way to undo the offending nut and it removed broken/stuck locking wheel nuts!!
Those are the ones I've got, they have an inverse thread so you do them up in the direction you would normally undo a nut, as you do that they bite down onto the wheelnut and undo it. They are great and make a mockery of most locking wheel nuts (except the really well designed ones).
2tongues The Subaru garage I went to when I had a Legacy had a wheel nut that wound on to the locking nut and cut into it, then turn the nut the way to undo the offending nut and it removed broken/stuck locking wheel nuts!!
Those are the ones I've got, they have an inverse thread so you do them up in the direction you would normally undo a nut, as you do that they bite down onto the wheelnut and undo it. They are great and make a mockery of most locking wheel nuts (except the really well designed ones).
15-03-2017, 11:21 AM
Lexus IS200 Sport Navigator (Now being stripped again) :blink:
Now Don't Forget The REP!!!
Screwfix do a set of locking wheel nut extractors? CLICK ME? not sure if it would be worth seeing if they will do the job mate? probably need to measure the outside of the broken nut to see if they would fit over it?
Lexus IS200 Sport Navigator (Now being stripped again) :blink:
Now Don't Forget The REP!!!
15-03-2017, 11:44 AM
steviewevie Luckily I do have a few spare wheel nuts, because I got a set of 20 (5 for each wheel), and I've got locking wheel nuts too, i.e. I've got 5 spare.
5 spare ay! surely 4 or you'll be a nut short lol
looks a tidy bit of exhaust under the car mate, nice job
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
15-03-2017, 11:44 AM #1,007steviewevie Luckily I do have a few spare wheel nuts, because I got a set of 20 (5 for each wheel), and I've got locking wheel nuts too, i.e. I've got 5 spare.
5 spare ay! surely 4 or you'll be a nut short lol
looks a tidy bit of exhaust under the car mate, nice job
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
17-03-2017, 07:11 AM
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
17-03-2017, 07:11 AM #1,009Good photos mate.
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
17-03-2017, 09:44 AM
Marsdendean Cut your wheel down like that other post from a different forum. I have cordless 18V respricating saw!
The car still OK steve?
You could also roll the arches with a metal post like that youtube video :Chair:
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
FirebirdPhil
17-03-2017, 09:44 AM #1,010Marsdendean Cut your wheel down like that other post from a different forum. I have cordless 18V respricating saw!
The car still OK steve?
You could also roll the arches with a metal post like that youtube video :Chair:
"Life's goal is not to arrive safely at the grave in a well preserved body. But, rather to skid in sideways........
totally worn out and broken, shouting 'Holy ****, WHAT A RIDE!'"
Recently Browsing
5 Guest(s)
5 Guest(s)
Recently Browsing
5 Guest(s)
5 Guest(s)
Related Threads…
Replies 1,312
Views 102,865
Views 102,865
25-03-2024, 02:10 AM
Last Post byZAIS200
Last Post by
Replies 1,341
Views 67,906
Views 67,906
08-02-2024, 01:53 AM
Last Post byWayne
Last Post by
Replies 4
Views 404
Views 404
18-12-2023, 02:55 AM
Last Post byRabster
Last Post by
Replies 20
Views 1,485
Views 1,485
08-10-2023, 03:59 AM
Last Post byWayne
Last Post by
Replies 42
Views 3,135
Views 3,135
04-10-2023, 03:52 PM
Last Post byWayne
Last Post by