Posty's IS200 SE
Posty's IS200 SE
13-03-2018, 09:22 AM
In a temporary position untill i sort out some other gauges and make a pod for them!
![[Image: picture225a.jpg]](http://img718.imageshack.us/i/picture225a.jpg/)
Im not too clued up on boost etc etc. but i get to a fraction under 0.3 when accelerating hard at about 5k revs.
Does this sound good or bad?
Well today I fitted the boost gauge I bought. It was a pig of a job, my hands just dont go into gaps that small. but i eventually won!
In a temporary position untill i sort out some other gauges and make a pod for them!
Im not too clued up on boost etc etc. but i get to a fraction under 0.3 when accelerating hard at about 5k revs.
Does this sound good or bad?
13-03-2018, 09:47 AM
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
That sounds about right Posty
Lexus IS200 Mods--TTE Supercharger, Tein Superstreet Coilovers & EDFC, 6000K HID Lights, HKS Silent High Power Exhaust, DBA Front Discs, Kenwood DNX9240 Head Unit, 19" Rims, TRD Kit, FIGS Bonnet Struts, Greddy Pillar Pod & Defi Gauges, TTE Red ARBS . And Been To WIM twice
13-03-2018, 11:57 AM
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
Sparkystav
13-03-2018, 11:57 AM #64That makes sense but i always fitted it before the changer when the airs not pressurized, it fitting it in the pressurised pipework you should make sure youve got a good seal
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
OutlawJapClub Admin Team
13-03-2018, 01:16 PM
dandydons thats the one mate.
Yerh, the hole/gash in the pipe was from Bandit, as it was from the air filter area, so the O2 sensor could get into it....
Latest Meets
[COLOR="Red"]Jap Show Finale 10,
Ace Cafe 16/10/10,
Miss Banzai Tunnel Run 16/10/10 -Car No: 368 -Tunnels Completed: 100%[/COLOR]
dandydons thats the one mate.
Yerh, the hole/gash in the pipe was from Bandit, as it was from the air filter area, so the O2 sensor could get into it....
Latest Meets
[COLOR="Red"]Jap Show Finale 10,
Ace Cafe 16/10/10,
Miss Banzai Tunnel Run 16/10/10 -Car No: 368 -Tunnels Completed: 100%[/COLOR]
13-03-2018, 02:36 PM
Bandit Think that hole might of been the one i had in it? i had an extension pipe there which was sealed into the hose for the air sensor :whistling:
it was a straight cut mate you couldnt put a extension piece in their it would never seal???
![[Image: ormiedit1-2.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/ormiedit1-2.jpg)
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Bandit Think that hole might of been the one i had in it? i had an extension pipe there which was sealed into the hose for the air sensor :whistling:
it was a straight cut mate you couldnt put a extension piece in their it would never seal???
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
14-03-2018, 02:52 PM
The hole for the sensor was approx two inches from the cone filter on the bottom...
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Tape won't seal a pressured system..
The hole for the sensor was approx two inches from the cone filter on the bottom...
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Recently Browsing
12 Guest(s)
12 Guest(s)
Recently Browsing
12 Guest(s)
12 Guest(s)
Related Threads…
Replies 1,312
Views 105,754
Views 105,754
25-03-2024, 02:10 AM
Last Post byZAIS200
Last Post by
Replies 1,341
Views 71,353
Views 71,353
08-02-2024, 01:53 AM
Last Post byWayne
Last Post by
Replies 4
Views 452
Views 452
18-12-2023, 02:55 AM
Last Post byRabster
Last Post by
Replies 20
Views 1,569
Views 1,569
08-10-2023, 03:59 AM
Last Post byWayne
Last Post by
Replies 42
Views 3,305
Views 3,305
04-10-2023, 03:52 PM
Last Post byWayne
Last Post by
Replies 28
Views 2,126
Views 2,126
17-05-2023, 11:25 AM
Last Post byIS200_rider
Last Post by