URGENT - Pipe bender/fabricator needed!
URGENT - Pipe bender/fabricator needed!
I do have a guy that can do it, after much searching. HOWEVER due to the fact he says he's going to have to make one of the bends in the same way you would on say a 2-stroke motorbike, i.e cutting bends and then tig welding them, then welding that bend into the rest of the custom pipe - it's going to cost me £250!
Does anyone know of someone/a company that could replicate the pipe for me, in the next couple of days cheaper than £250?!
ANY help/advice on this would be greatly appreciated!!
Otherwise I s'pose I'll just have to bite the bullet and stump up the £250 :ohmy:
Thanks!
![[Image: OJCSig.jpg]](http://i462.photobucket.com/albums/qq341/dh-all-the-way/OJCSig.jpg)
DanielWatts Banging 9.5J Wheels 'coz that's how you roll
Im after an experienced pipe bender/fabricator/some one 'in the trade' to replicate a pipe that Stoney has very kindly sent me from his supercharger kit.
I do have a guy that can do it, after much searching. HOWEVER due to the fact he says he's going to have to make one of the bends in the same way you would on say a 2-stroke motorbike, i.e cutting bends and then tig welding them, then welding that bend into the rest of the custom pipe - it's going to cost me £250!
Does anyone know of someone/a company that could replicate the pipe for me, in the next couple of days cheaper than £250?!
ANY help/advice on this would be greatly appreciated!!
Otherwise I s'pose I'll just have to bite the bullet and stump up the £250 :ohmy:
Thanks!
DanielWatts Banging 9.5J Wheels 'coz that's how you roll
Edit: Dah Pete beat me to it!
I had this problem getting a midpipe made for my old exhaust. Most exhaust places (longlife, powerflow etc) should be able to help as long as the pipe diameter is not too large. Loads of places can do 2" and 2.5" easily but 3" becomes more of a pain and gets expensive!
Edit: Dah Pete beat me to it!
![[Image: LexuS-Copy.jpg]](http://i65.photobucket.com/albums/h204/Sparkystav/LexuS-Copy.jpg)
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
Sparkystav
19-07-2018, 03:45 AM #5the pipe should be 50mm so shouldnt be an issue to an exhaust place
Read my thread here: The Evolution of my Turbo Lexus from NA-Supercharged-Twin Turbo-Massive Single
Please leave your comments.
![[Image: 2011-08-18230538.jpg]](http://i193.photobucket.com/albums/z164/blatrat/2011-08-18230538.jpg)
![[Image: ormiedit1-2.jpg]](http://i214.photobucket.com/albums/cc320/tempra5/ormiedit1-2.jpg)
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
Can you not make it out of straight pipes and use silicon elbows/bends for the bends??
TTE supercharger,pr0lex manifold,hks fcd,larger intercooler,apexi induction kit,silicone hose kit,IK22's,polished engine parts,TTE front bumper mod'd for intercooler,TRD side skirts,TRD rear lip,JDM headlights and fogs,10k hid headlights 8k full beam,L8XSS p/plate,fog/brake/light conversion,18"fox rs's,lowered 90mm(f)100mm®,moleys under bars,yellow trd anti rollbars,full stainless exhaust,carbon fiber intake plus so much more
3 Guest(s)
3 Guest(s)
Views 347
Last Post by
Views 658
Last Post by
Views 1,200
Last Post by
Views 617
Last Post by
Views 413
Last Post by
Views 440
Last Post by
Views 493
Last Post by
Views 589
Last Post by