Stix's IS200

JapCarForum Cars, Cars, Cars! Project Cars Stix's IS200

Stix's IS200

Pages (45): Previous 1 … 32 33 34 35 36 … 45 Next

S
Banned

1,153

28-12-2019, 01:47 PM

#331

Thanks stav, I'll try replacing the tensioner. The bolt really couldn't get any tighter Smile

S

28-12-2019, 01:47 PM #331

Thanks stav, I'll try replacing the tensioner. The bolt really couldn't get any tighter Smile

eogbaker
Member

148

28-12-2019, 05:07 PM

#332

Might not be the actual bolt or pulley just might need to get someone to apply a lot more pressure on it before tightening the centre bolt.

eogbaker

28-12-2019, 05:07 PM #332

Might not be the actual bolt or pulley just might need to get someone to apply a lot more pressure on it before tightening the centre bolt.

S
Banned

1,153

29-12-2019, 09:14 AM

#333

I had big Brian push the tensioner while I tightened the bolt so I don't think it could be tensioned any better haha! I'll try a new tensioner, its only £30 or something! haha

S

29-12-2019, 09:14 AM #333

I had big Brian push the tensioner while I tightened the bolt so I don't think it could be tensioned any better haha! I'll try a new tensioner, its only £30 or something! haha

S
Banned

1,153

11-01-2020, 02:38 PM

#334

decided to update this Smile

Had my manifold modded so the lambda doesn't hit the side of the engine bay and heat wrapped it:

[Image: IMAG0313.jpg]

I Heat wrapped the Y-Pipe (yes I ran out but I've been and bought more):

[Image: IMG-20130216-WA0012.jpg]

Now my car is quite low so my Y-Pipe hits the floor ALL THE TIME so I realised that my heat wrap wont last two minutes so I made a skid plate for it!

[Image: IMAG0294-1.jpg]

I know the skid plate looks a bit pikey but all I had was an angle grinder and a bench vice so all the bends were made by hand! plus its only going to get bashed up so it doesn't need to be pretty! haha

I still need to drill holes in the side so I can attach it to the Y-Pipe.

Thats a job for the weekend though.

S

11-01-2020, 02:38 PM #334

decided to update this Smile

Had my manifold modded so the lambda doesn't hit the side of the engine bay and heat wrapped it:

[Image: IMAG0313.jpg]

I Heat wrapped the Y-Pipe (yes I ran out but I've been and bought more):

[Image: IMG-20130216-WA0012.jpg]

Now my car is quite low so my Y-Pipe hits the floor ALL THE TIME so I realised that my heat wrap wont last two minutes so I made a skid plate for it!

[Image: IMAG0294-1.jpg]

[Image: IMAG0293.jpg]

I know the skid plate looks a bit pikey but all I had was an angle grinder and a bench vice so all the bends were made by hand! plus its only going to get bashed up so it doesn't need to be pretty! haha

I still need to drill holes in the side so I can attach it to the Y-Pipe.

Thats a job for the weekend though.

S
Banned

1,153

12-01-2020, 03:10 PM

#335

So I finished the Y-pipe:

[Image: IMAG0316_BURST002.jpg]

I then fitted it along with the supercharger and the straight adapter for the SSQV Smile

I also replaced the screws in the throttle body that hold the SC and throttle cable in place. Mainly because the screws seem to round off every time I remove them and it annoyed me.

I also sorted all of the joins in my exhaust so it doesn't blow anymore Smile

S

12-01-2020, 03:10 PM #335

So I finished the Y-pipe:

[Image: IMAG0316_BURST002.jpg]

I then fitted it along with the supercharger and the straight adapter for the SSQV Smile

I also replaced the screws in the throttle body that hold the SC and throttle cable in place. Mainly because the screws seem to round off every time I remove them and it annoyed me.

I also sorted all of the joins in my exhaust so it doesn't blow anymore Smile