JapCarForum Cars, Cars, Cars! Project Cars Yellow IS200

Yellow IS200

Yellow IS200

Pages (20): Previous 116 17 18 19 20 Next  
Wayne
Senior Member
607
23-01-2024, 12:28 PM
Throwing up a P0110 fault, so I'm assuming I've stressed the wires on the intake sensor.
Wayne
23-01-2024, 12:28 PM #181

Throwing up a P0110 fault, so I'm assuming I've stressed the wires on the intake sensor.

Wayne
Senior Member
607
04-02-2024, 09:10 AM
Got myself one of them fancy cable operated bypasses. Car keeps jumping into limp mode. Gotta rotate my bypass pipe though.


[Image: 3176vr8.jpg]
Wayne
04-02-2024, 09:10 AM #182

Got myself one of them fancy cable operated bypasses. Car keeps jumping into limp mode. Gotta rotate my bypass pipe though.


[Image: 3176vr8.jpg]

Sparkystav
Administrator
14,683
04-02-2024, 09:42 AM
It keeps going in limp with the new bypass? Any codes?

Could be the throttle too tight


Sent from my iPad using Tapatalk

OutlawJapClub Admin Team
Sparkystav
04-02-2024, 09:42 AM #183

It keeps going in limp with the new bypass? Any codes?

Could be the throttle too tight


Sent from my iPad using Tapatalk


OutlawJapClub Admin Team

Wayne
Senior Member
607
04-02-2024, 02:23 PM
Nah car is going into limo mode with the old bypass, ain't had chance to try the cable one, linkage is fouling on my inlet so need to change it... Again
Wayne
04-02-2024, 02:23 PM #184

Nah car is going into limo mode with the old bypass, ain't had chance to try the cable one, linkage is fouling on my inlet so need to change it... Again

Sparkystav
Administrator
14,683
05-02-2024, 10:45 AM
Ah right


Sent from my iPad using Tapatalk

OutlawJapClub Admin Team
Sparkystav
05-02-2024, 10:45 AM #185

Ah right


Sent from my iPad using Tapatalk


OutlawJapClub Admin Team

P.Nicolov
Junior Member
13
07-02-2024, 08:14 AM
Mate, it seems that just extending the short pipe for the bypass will do the trick. Or rotating it. But a bit of welding is inevitable Smile It's going to be worth it, so don't get frustrated by some metalwork Big Grin

Very nice build btw!
P.Nicolov
07-02-2024, 08:14 AM #186

Mate, it seems that just extending the short pipe for the bypass will do the trick. Or rotating it. But a bit of welding is inevitable Smile It's going to be worth it, so don't get frustrated by some metalwork Big Grin

Very nice build btw!

Wayne
Senior Member
607
07-02-2024, 12:08 PM
Aye it'll get there, may have a few more grey hairs before it's running right though Big Grin
Wayne
07-02-2024, 12:08 PM #187

Aye it'll get there, may have a few more grey hairs before it's running right though Big Grin

Wayne
Senior Member
607
18-02-2024, 01:05 PM
Finally got my cabe bypass fitted (I'll get some pics up tomorrow)! The round the block I did for 'testing' seems to have gone good. No limp mode, even when holding it at part throttle down a dual carriageway. I'll find out more tomorrow! But fingers cross I can freely drive now.

Massive thanks to Plamen, not only for the part but for the advice. I've also ordered a 150mm pulley from him, so depending on when I can get my hands on some 1ZZ injectors it may well be done by Japfest!
Wayne
18-02-2024, 01:05 PM #188

Finally got my cabe bypass fitted (I'll get some pics up tomorrow)! The round the block I did for 'testing' seems to have gone good. No limp mode, even when holding it at part throttle down a dual carriageway. I'll find out more tomorrow! But fingers cross I can freely drive now.

Massive thanks to Plamen, not only for the part but for the advice. I've also ordered a 150mm pulley from him, so depending on when I can get my hands on some 1ZZ injectors it may well be done by Japfest!

Sparkystav
Administrator
14,683
19-02-2024, 10:19 AM
Cant wait to see it mate


Sent from my iPad using Tapatalk

OutlawJapClub Admin Team
Sparkystav
19-02-2024, 10:19 AM #189

Cant wait to see it mate


Sent from my iPad using Tapatalk


OutlawJapClub Admin Team

Wayne
Senior Member
607
19-02-2024, 12:36 PM
Sparkystav Cant wait to see it mate


Sent from my iPad using Tapatalk

Still not 100%, but no limp mode or anything of the sort, the linkage is just catching on my silicone bend, so I'm either gonna have to make a plate up to raise the bypass slightly or get a longer pipe welded on. A plate will be my first port of call, reckon it'll leak though. I'l just gasket weld the **** out of it. :whistling:

Injectors have been ordered, anyone know of a reputabe place I can get O-rings from?
Wayne
19-02-2024, 12:36 PM #190

Sparkystav Cant wait to see it mate


Sent from my iPad using Tapatalk

Still not 100%, but no limp mode or anything of the sort, the linkage is just catching on my silicone bend, so I'm either gonna have to make a plate up to raise the bypass slightly or get a longer pipe welded on. A plate will be my first port of call, reckon it'll leak though. I'l just gasket weld the **** out of it. :whistling:

Injectors have been ordered, anyone know of a reputabe place I can get O-rings from?

Pages (20): Previous 116 17 18 19 20 Next  
Recently Browsing
 1 Guest(s)
Recently Browsing
 1 Guest(s)
Related Threads…
Replies 91
Views 5,047
09-04-2024, 01:09 AM
Last Post by Sparkystav
Replies 21
Views 1,267
06-04-2024, 05:57 PM
Last Post by Lexuspat
Replies 1,312
Views 102,696
25-03-2024, 02:10 AM
Last Post by ZAIS200
Replies 414
Views 20,144
18-02-2024, 11:42 PM
Last Post by is200turbo
Replies 1,341
Views 67,544
08-02-2024, 01:53 AM
Last Post by Wayne
Replies 4
Views 404
18-12-2023, 02:55 AM
Last Post by Rabster
Replies 20
Views 1,469
08-10-2023, 03:59 AM
Last Post by Wayne
Replies 42
Views 3,110
04-10-2023, 03:52 PM
Last Post by Wayne
Replies 28
Views 1,927
17-05-2023, 11:25 AM
Last Post by IS200_rider
Replies 83
Views 4,279
06-05-2023, 06:32 AM
Last Post by Niliano